TM-9-2350-238-24P-1
RECOVERY VEHICLE, FULL TRACKED: LIGHT ARMORED, M578
UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS
MAY 1994
TM-9-2350-238-24P-1 - Page 16 of 673
TM 9-2350-238-24P- 1
3. EXPLANATION OF COLUMNS (SEC -
TIONS II AND Ill) (CONT).
(9)
The statement “END OF FIGURE”
appears just below the last item description in
Column 5 for a given figure in both Section II
and Section III.
f. QTY (Column (6)).
The QTY (quantity per
figure column) indicates the quantity of the item
used in the breakout shown on the illustration
figure, which is prepared for a functional group,
subfunctional group, or an assembly. A “V”
appearing in this column in lieu of a quantity
indicates that the quantity is variable and the
quantity may vary from application to applica-
tion.
4. EXPLANATION OF COLUMNS (SEC -
TION IV).
a. National Stock Number (NSN) Index .
(1) STOCK NUMBER column.
This col -
umn lists the NSN by National Item Identification
Number (NIIN) sequence. The NIIN consists of
the last nine digits of the NSN
NS N
(i.e., 5305-01 -674-1467). When using this
NIIN
column to locate an item, ignore the first 4 digits
of the NSN. However, the complete NSN
should be used when ordering items by stock
number .
(2) FIG. column.
This column lists th e
number of the figure where the item is identi-
fied/located. The figures are in numerical order
in Section II and Section III.
(3) ITEM column.
The item number iden-
tifies the item associated with the figure listed in
the adjacent Figure column. This item is also
identified by the NSN listed on the same line.
b. Part Number Index.
Part numbers in this
index are listed by part number in ascending
alphanumeric sequence (i.e., vertical arrange-
ment of letter and number combination which
places the first letter or digit of each group in
order A thru Z, followed by the numbers 0 thru 9
and each following letter or digit in like order).
(1) CAGEC column.
The Commercia l
and Government Entity Code (CAGEC) is a 5-
digit numeric code used to identify the manu-
facturer, distributor, or Government agency, etc.,
that supplies the item.
(2) PART NUMBER column.
Indicate s
the primary number used by the manufacturer
(individual, firm, corporation, or Government
activity), which controls the design and charac-
teristics of the item by means of its engineering
drawings, specifications standards, and inspec-
tion requirements to identify an item or range of
items .
(3) STOCK NUMBER column.
This col -
umn lists the NSN for the associated part num-
ber and manufacturer identified in the PART
NUMBER and CAGEC columns to the left.
(4) FIG. column.
This column lists th e
number of the figure where the item is identi-
fied/located in Sections II and III.
(5) ITEM column.
The item number is
that number assigned to the item as it appears
in the figure referenced in the adjacent figure
number column.
c. Figure and Item Number Index .
(1) FIG. column.
This column lists th e
number of the figure where the item is identi-
fied/located in Sections II and III.
(2) ITEM column.
The item number is
that number assigned to the item as it appears
in the figure referenced in the adjacent figure
number column.
(3) STOCK NUMBER column.
This col -
umn lists the NSN for the item.
(4) CAGEC column.
The Commercia l
and Government Entity Code (CAGEC) is a 5-
digit numeric code used to identify the manu-
facturer, distributor, or Government agency, etc.,
that supplies the item.
6
Back to Top
