TM-9-2815-210-34-2-1
ENGINE ASSEMBLY, DIESEL (MULTIFUEL): NATURALLY ASPIRATED OR TURBOCHARGED, FUEL-INJECTED, WATER-COOLED, 6-CYLINDER
TECHNICAL MANUAL; TROUBLESHOOTING; DIRECT SUPPORT AND GENERAL SUPPORT LEVEL; VOLUME 2 OF 2; PART 1 OF 2
APRIL 1981
TM-9-2815-210-34-2-1 - Page 19 of 259
TM 9-2815-210-34-2-1
1-5. TORQUE VALUES.
Critical torque values for a particular component are given
in the maintenance procedures.
When torque values are not given, bolts, screws and
nuts are to be tightened as given in table 1-1.
1-6. SPECIAL TOOLS AND EQUIPMENT.
Special tools and equipment are provided
to make it easier to do particular maintenance tasks and to keep the equipment in
good repair.
Table 1-2 lists the special tools and equipment and gives reference
to the maintenance paragraph where they are used and what they are used for.
1-7. SAFETY INSPECTION AND TESTING OF LIFTING DEVICES.
Refer to
TB 43-0142 for safety inspection and testing of lifting devices used in this manual.
1-8. FORMS AND RECORDS.
Maintenance forms, records, and reports which are to
be used by maintenance personnel at all levels are listed in and prescribed by
TM 38-750.
1-9. EQUIPMENT IMPROVEMENT REPORT AND MAINTENANCE DIGEST (EIR MD)
AND EQUIPMENT IMPROVEMENT REPORT AND MAINTENANCE SUMMARY (EIR MS).
The quarterly Equipment Improvement Report and Maintenance Digest, TB 43-0001-39
series, contains valuable field information on the equipment covered in this manual.
The information in the TB 43-0001-39 series is compiled from some of the Equipment
Improvement Reports that you prepared on the engines covered in this manual. Many
of these articles result from comments, suggestions,
and improvement recommenda-
tions that you submitted to the EIR program.
The TB 43-0001-39 series contains
information on equipment improvements, minor alterations, proposed Modification Work
Orders (MWO’s), warranties (if applicable), actions taken on some of your DA Form
2028’s (Recommended Changes to Publications), and advance information on proposed
changes that may affect this manual.
In addition, the more maintenance significant
articles, including minor alterations,
field-fixes, etc, that have a more permanent
and continuing need in the field are republished in the Equipment Improvement Re-
port and Maintenance Summary (EIR MS) for TACOM Equipment (TM 43-0143).
Refer to both of these publications (TB 43-0001-39 series and TM 43-0143) periodical-
ly, especially the TB 43-0001-39 series,
for the most current and authoritative infor-
mation on your equipment.
The information will help you in doing your job better
and will help in keeping you advised of the latest changes to this manual. Also
refer to DA Pam 310–4, Index of Technical Publications, and Appendix A, Refer-
ences, of this manual.
1-10. REPORTING IMPROVEMENT RECOMMENDATIONS.
If your equipment needs
improvement, let us know.
Send us an EIR.
You, the user, are the only one who
can tell us what you don’t like about your equipment. Let us know why you don't
like the design.
Tell us why a procedure is hard to perform. Put it on an SF 368
(Quality Deficiency Report) . Mail it to us at:
Commander, U.S. Army Tank-Auto-
motive Command, ATTN: DRSTA-MT. Warren, Michigan 48090. We'll send you a reply.
1-11. METRIC SYSTEM.
The equipment /system described herein is nonmetric and
does not require metric common or special tools.
Therefore, metric units are not
supplied.
Tactical instructions, for sake of clarity, will also remain nonmetric.
1-12. DESTRUCTION TO PREVENT ENEMY USE.
Follow procedures given in
TM 750-244-6 for destruction of Army material to prevent enemy use.
-
1-13. ADMINISTRATIVE STORAGE.
Requirements for Administrative
covered in TM 740-90-1.
Storage are
1-5
Back to Top
