TM-9-2320-272-23-4

TRUCK, 5-TON, 6X6, M939, M939A1, AND M939A2 SERIES TRUCKS (DIESEL)

TECHNICAL MANUAL; FIELD MAINTENANCE MANUAL; VOLUME 4 OF 5

SEPTEMBER 2012
TM-9-2320-272-23-4

  TM-9-2320-272-23-4 - Page 1051 of 1393

REMOVAL
1.
Remove cotter pin (Figure 1, Item 13), washer (Figure 1, Item 38), and clevis pin (Figure 1, Item 39) from cable
clevis (Figure 1, Item 25) and shift lever arm (Figure 1, Item 6). Discard cotter pin.
2.
Remove four locknuts (Figure 1, Item 12), screws (Figure 1, Item 9), and shift lever (Figure 1, Item 10) from
two shift lever brackets (Figure 1, Item 8), shims (Figure 1, Item 11), and floor (Figure 1, Item 41).
Discard
locknuts.
3.
Remove woodruff key (Figure 1, Item 4) from shift lever rod (Figure 1, Item 10).
4.
Remove locknut (Figure 1, Item 7), screw (Figure 1, Item 5), and shift lever arm (Figure 1, Item 6) from cab
floor (Figure 1, Item 41). Discard locknut.
5.
Remove two shift lever brackets (Figure 1, Item 8) from shift lever rod (Figure 1, Item 10).
6.
Remove six locknuts (Figure 1, Item 40), screws (Figure 1, Item 3), seal (Figure 1, Item 2), and retainer ring
(Figure 1, Item 1) from cab floor (Figure 1, Item 41). Discard locknuts.
7.
Loosen and remove cable clevis (Figure 1, Item 25) and jamnut (Figure 1, Item 24) from dump valve cable
(Figure 1, Item 32).
8.
Remove two locknuts (Figure 1, Item 21), screws (Figure 1, Item 27), clamp (Figure 1, Item 26), and shim
(Figure 1, Item 23) from cable conduit (Figure 1, Item 28) and rear cab floor left bracket (Figure 1, Item 22).
Discard locknuts.
9.
Remove locknut (Figure 1, Item 20), screw (Figure 1, Item 30), and clamp (Figure 1, Item 29) from cable conduit
(Figure 1, Item 28) and rear cab floor right bracket (Figure 1, Item 19). Discard locknut.
10.
Remove tiedown strap (Figure 1, Item 31) from cable conduit (Figure 1, Item 28). Discard tiedown strap.
11.
Remove cotter pin (Figure 1, Item 17), washer (Figure 1, Item 16), and clevis pin (Figure 1, Item 15) from cable
clevis (Figure 1, Item 14) and control valve (Figure 1, Item 18). Discard cotter pin.
12.
Loosen and remove cable clevis (Figure 1, Item 14) and jamnut (Figure 1, Item 37) from dump valve cable
(Figure 1, Item 32).
13.
Remove jamnut (Figure 1, Item 37) and washer (Figure 1, Item 36) from control valve (Figure 1, Item 18) side
of cable conduit (Figure 1, Item 28) and lower bracket (Figure 1, Item 35).
14.
Pull cable conduit (Figure 1, Item 28) through lower bracket (Figure 1, Item 35). Remove washer
(Figure
1,
Item 34) and nut (Figure 1, Item 33) from cable conduit. Tag for installation.
TM 9-2320-272-23-4
0716
0716-2


Back to Top