TM-9-2520-254-34

TRANSMISSION, AUTOMATIC, ALLISON, MODEL TX100-1

TECHNICAL MAUAL; DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL

OCTOBER 1971
TM-9-2520-254-34

  TM-9-2520-254-34 - Page 44 of 126

Table 3-1.
Special
Tools
and Equipment for Direct and General Support Maintenance
BOLT (2)
BOLT, puller (3)
COMPRESSOR
EYE, lifting
GUIDE BOLT SET
HANDLE
HOLDER ASSEMBLY
KIT, pressure gage
KIT, remover and replacer
KIT, snap ring
PULLER
ASSEMBLY
REPLACER
REPLACER
REPLACER
REPLACER
REPLACER
SLING
STAND
STRAP, lifting
Ref
Item
15
10
4
14
17
13
5
3
16
2
7
6
8
l 2
11
1
9
Fig.
3-1
3-1
3-1
3-1
3-1
3-1
3-1
3-2
3-1
3-1
3-1
3-1
3-1
3-1
3-1
3-1
3-1
3-3
3-1
Identifying
numbers
8356186 (19207)
8356200 (19207)
8356187 (19207)
10865773(19207)
7950864 (19207)
8356195 (19207)
8356176 (19207)
8356170 (19207)
8356191 (19207)
8356201 (19207)
8356173 (19207)
8356204 (19207)
8356184 (19207)
Use reference
Figure
5-30
5-105
5-108
5-32
5-109
5-36
5-44
5-95
5-102
5-20
5-34
5-106
5-120
5-65
5-88
5-91
5-108
5-111
5-57
5-64
5-69
5-79
5-85
5-87
5-60
5-143
5-44
5-68
5-70
5-71
5-73
5-117
5-118
5-17
5-64
5-69
5-85
5-57
5-79
5-1
5-140
5-2
5-3
5-140
5-20
5-120
Par.
5-6
5-58
5-58
5-6
5-58
5-6
5-6
5-58
5-58
5-6
5-6
5-58
5-58
5-16
5-58
5-58
5-58
5-58
5-11
5-16
5-21
5-41
5-58
5-58
5-11
5-62
5-62
5-18
5-21
5-21
5-21
5-58
5-58
5-6
5-16
5-21
5-58
5-11
5-41
5-6
5-58
5-6
5-6
5-58
5-6
5-58
Use
To hold intermediate clutch back
plate in position during buildup
and disassembly.
To remove ground sleeve diaphragm
assembly.
To compress and hold low, reverse,
and intermediate clutch package
during installation and removal,
and compress reverse clutch pack
to remove or install holding pins.
To lift high-range clutch package and
converter drive cover; used with
To position front and rear oil pumps,
and front and rear pitot tubes and
diaphragm.
To install front oil pump seal, install
high clutch housing bushing, install
output bearing and seal, install
converter drive cover bushing and
output shaft bushing; used with
replacers
.572 -8658, 5120-572-8615, 5120-
572-8656,
To hold stator freewheel rollers and
springs in place to assemble race.
To check transmission oil pressures.
To install and remove clutch piston
return spring retaining ring.
To install turbine shaft snap rings.
To remove output seal.
To install front oil pump seal: used
with handle .5120 -316-9182.
To install high clutch housing
bushing: used with handle 5120-
310-9182.
T
O install output bearing and oil seal;
used with handle ,5120-316-9182.
To install converter drive cover
bushing:
used with handle .5120 -
316-9182.
To install output shaft bushing: used
with handle .5120 -316-9182.
To lift transmission and to mount
transmission in stand.
To hold and position transmission for
teardown and build up.
T
O remove or install converter drive
cover. and check mounting space;
used with lifting eye 4910-673-
3801.
3-3


Back to Top