TM-9-2815-220-34
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED, 12-CYLINDER, ASSEMBLY; MODELS AVDS-1790-2C (2815-00-410-1203) AND AVDS-1790-2D (2815-00-410-1204)
TECHNICAL MANUAL; DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL
TM-9-2815-220-34 - Page 450 of 532
TM 9-2815±220²34
³
-
STRIP CABLE INSUlATIOn EQUAL TO DEpTH OF SOLDER WELLS Of
´
±
REMoVE GROmmET RETAInInG nuT fROM pL±G ASSEmbLY
i²SeRTS.
And SLIdE BAcK OVER cAB³E´
µ
²
SLµ¶E GROmMET BA·k fROm pLUG ASS¸mBLY An¶ REmOVE
¶AmAGE¶ CABLE
¶
³
pASS REpLAcEmEnT CABLE thROUGh
GROmmET RETAInInG
¹UT
Anº
GROmMET InSER» ¼n»O SOL¶½R wELLS OF InS½RTS¾
An¶ SOL¶ER¿
·
´
SLIÀE GROmmET OVER InSERTS AND pRESS I²TO pLUG
ASSEmBLY U²TIL SEATE¶Á
6
µ
»ÂREA¶ GROmmET RETAInInG nû TO pLÄG ASSEmBLyÁ
TYpIÅAL mALE-ÆYÇE pLÈG ASSEmBLY
TA028615
Fgure
3.07±
Replacemen¸ of cObLe ¹ºLe reCeptºc»e¼.
N½¾E
RubBer-to-±UbbEr conTaC²s of BEll³´ypE CoNµ
NEcTO¶S mAy · l¸BricA´Ed
ligh´Ly
wITh
SiliCo¹E compoUNd Mº»¼½¾6 T¿ AssÀS´ ASÁ
SÂmbly.
c.
IMtalL±²ion of Jumper W³RE.
Ão SUBSÄiTUÅ A
j¸mpEr wiÆE for A dEfEcTivE HArNÇS wirE, TApE ´HE
j¸mPr wirE T¿ ´HE Ex´Erior oF ThE hArNESS; do No´ diSµ
ASSÂmBlE TÈE hArnÂSSÉ DISASSEmBlE ´hE CoNNÊc´o±S AS
ShowN IN fiGurES
¿À
or
ÁÂ
ANd unSoldEr ´HE dEËECµ
TIvE wIrEÌ Í´rip ThE iNS¸LA´IoN From ´HE ENd of ´hE
j¸mÎÂr wIrÏ ´o ThE dEp´h of ThE SoLdEr wELL oN ´hE CoNÁ
taCT inSEÐ´Ñ ÒASS ÄhE J¸mpEr wi¶E ThÓÔUgH THE g¶ommE´
ÕÖÄ×iNing NUT ANd g¶ommEÄ, And SoldEr To THE iNSEд.
REASSEmBlÏ THE coNNÊcT¿rÌ
dÃ
Ø CABlE ThA´ hAS BÂÊN ¶EpAi¶Ed by iNSTAllIng A
jUmpEr wIrÊ SHo¸ld BE BrUSHÊd or Spr'ÙyÂd wIÄh ElEc´riÚ
cAl
INS¸LAÄINg
compouNd
(igNiTioN) MÛÜ-V³13ÝÞßÑ
ØLLow ´HE comà¸Nd ´¿ dry ár ApproximA´Ely
Ä
Hou±â
BÊfãrE hAndLiNgä åhE Compo¸Nd iS NoT A Cond¸cær of
ElÂcTrIcIçyè So CArE m¸ST BE TAkEN TO AvoId ovE¶SprAyiNg
THE compo¸Nd on conTacT S¸¶ËAcEé of wiÐE TErmINAlSê
coNNEC´¿r CoN´Acëì or SimiLAr pArçS wHErÊ i´ wIll prEµ
vEN´ ´hE flow of ELEcTrIíIÄyä
ÅÆÇÈÈÉ
Assembly
îNS´Alï ´HE wiriNg HArNÇS ASSÂmbLy ço THE powEr pLANð
AS oUTLINÊd iN pArAg¶ApH 2ñ9(ò) óor ´HE Ø VD½ôõ7ö¼÷
ENgiNE ASSEmbLyì ANd pArAg¶Aph
2øùúû2ü for THE
ØVD½-1ýö¼ò0 EngInE ASSÂmBLyþ
SEction XXVlL. G±N±RA² ASS±MB³Y PROC±DUR±S
ÅÊËÈÌÍ
Clea´lIµess
ÿHE ENgINE ĀS
a
p±ÂciSioN p±ā¸CÄ ANd Ex´±ÊmE cArE ANd
clEAnLinEss øST BE ExE¶cISEd In AlL pHASES of AssEmbly
oÎÂrATIoNS
t
iNS¸¶E â×TiSfAc´o±y ENgiNE pÂrformAncEă
DI¶ç ANd duéT, EvEN iN mIN¸TE quANTITieS, ArE AbrASIvEþ
ØF´Êr ClEANiNg ANd J¸S´ bEforE AssÊmbLyĄ c¿A´ ALl ·Arą
IngS, ShAĆTSĄ ANd coNT×CT SU¶fAcć wITh ENgiNE oIl
(ÎÏ)Ð
åHIS will INĈ¸rE SUffIciEN´ L¸brICATioN of movINg pAr´s
wHEN fIÕâ´ ĉ¸T IN´o opErATIoNĊ
ÑÒÓ20
ÅÔËÈ7Í
GE´er¶L AssembLy ·´sT¸u¹tiº´s
a
ØLwAyS ¸SÂ NEw gASkEċS wHEn ASSEmblINg THE
ENgInEČ čSE nEw p¶EFormÂd pAcKiNĎS ANd AnNUlAr CopÁ
Pr gASKEÄS THr¿¸gHoU´ EngInE ASSEmblyď Øn ENgInE
ovErhA¸l pAÐĐ kIT 57đ48 coNSIS´iNg of All nÊcÊĒAÕY
gASkE´s And p¶EfãrmEd pACkInĎé, iS AvAiLAblE for ¸SE
dUrIng EngInE ¶ÊpAIrČ
BÕ
ēvErAl oĔ ´hE CompoNEnÄS of THE ENgINE AÐÊ AvAILµ
AbLE IN KITS or sÊçsĕ WHEnEvEr A KIT or sE´ IS UsÊd For
)
¶
Back to Top
