TM-1-1500-344-23-4
CONSUMABLE MATERIALS AND EQUIPMENT FOR AIRCRAFT AND AVIONICS VOLUME IV
TECHNICAL MANUAL; CLEANING AND CORROSION CONTROL
SEPTEMBER 2013
TM-1-1500-344-23-4 - Page 66 of 92
3-8
NAVAIR 01-1A-509-4
TM 1-1500-344-23-4
01 September 2013
Table 3-2. Corrosion Removal Equipment (Cont.)
Nomenclature
Specifcation/
Part No.
National Stock
Number
Unit
of
Issue
Intended Use
Usable On
AC
AV
Dry Honing Machine,
Portable, Air-Operated
CVB-42007 (Junior)
(Vacublast)
EA
A compact, self-contained, light weight honer
used for the removal of corrosion products
from aircraft and components.
X
X
Air Nozzle Gun
A-A-55543
(supersedes
GGG-G-770)
EA
Use to remove chips, dirt, and waste
material from machines, work pieces, or
benches.
X
X
Air Hose Assembly,
General Purpose
ZZ-H-521
3/8" ID x 50'
ZZ-H-500
5/8" ID x 50'
3/4" ID x 50'
FT
FT
FT
Use for painting and vacu-blasting.
X
Coupling Half, Air Hose,
Low Pressure, Quick
Disconnect
MIL-C-4109
Male quick disconnect
1/4" NPT/M
3/8" NPT/M
3/8" Hose Shank/M
1/2" NPT/M
1/2" Hose Shank/M
3/4" NPT/M
Female quick disconnect
1/4" NPT/F
3/8" NPT/F
3/8" Hose Shank/F
1/2" NPT/F
1/2" Hose Shank/F
3/4" NPT/F
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
Male quick disconnect half for use with
pneumatic tools and paint spray guns.
Male quick disconnect half for use with
portable dry honing machines.
Female quick disconnect half for use with
pneumatic tools and paint spray guns.
Female quick disconnect half for use with
portable dry honing machines.
X
Hose Clamp
A-A-52506
(supersedes
WW-C-440)
EA
Metal hose clamps used for holding ±exible
ducts or hose on to a male ²tting.
X
Hand Pad Holder
3M No. 952
(INSTA-LOK)
Open Purchase
EA
Hand tool for holding abrasive pads. For use
with Abrasive Mat, A-A-58054.
X
Disc Sander Pad
3M No. 051144-05576
EA
Back-up pad to run 6" dia. abrasive paper
discs. Use with a dual motion sander. For
use with Abrasive Paper Discs, A-A-2697.
X
Mandrel
3M No. 933, 1" washer
(2" length x 1/4" shank)
3M No. 934, 2 1/2"
washer
(3 1/16" length x 1/4"
shank)
3M No. 935, Mini Mandrel
(2 7/8" length x 1/4"
shank)
EA
EA
EA
For use with Finishing Flap Brush No. 5AFIN
or 5AMED (see Table 2-1). Use with 2" - 3"
diameter discs.
Use with 3"-6" diameter discs.
Use with 1" x 1.5" pieces of abrasive
material to ²t into tight areas.
X
Disk Pad Holder, Hook
and Loop
3M No. 9215
(1.5" dia. x 1/4" shank)
3M No. 923
(3" dia. x 1/4" shank)
Open Purchase
EA
EA
Back-up pad to run surface conditioning
discs. Use with a drill. For use with Surface
Condition Discs (see Table 2-1).
X
Back to Top
