TM-5-3805-254-14-P-2
TRUCK, DUMP, 20 TON, 6X4, ON-OFF HIGHWAY 71,000 GVW, IHC MODEL F-5070 (CCE)
TECHNICAL MANUAL; OPERATOR’S, ORGANIZATIONAL, DIRECT SUPPORT, GENERAL SUPPORT AND DEPT MAINTENANCE MANUAL (INCLUDING REPAIR PARTS INFORMATION AND SUPPLEMENTAL MAINTENANCE INSTRUCTIONS)
JUNE 1980
TM-5-3805-254-14-P-2 - Page 724 of 894
TRUCK SERVICE MANUAL
TRANSMISSIONS
GENERAL OVERHAUL INFORMATION
Para 4-2
SPECIAL TOOLS TABLE (fig. 4-2, 4-3, 4-4)
Fig
Item
Tool No. *
Description
Use illustrated
4-2
1
J24204
Clutch spring compressor set
2
J24204-1
Low and first clutch spring compressor
Fig. 6-53
3
J24204-2
Bar and study assembly
Fig. 6-41, 6-53
4
J24204-3
Forward and fourth clutch spring
Fig. 6-41
compressor
4-2
5
J24195
Center support lifting bracket
Fig. 7-5, 7-17,
7-24, 5-35
4-2
6
J24208
Center support compressor assembly
7
J24208-2
Center support compressor sleeve
Fig. 7-6
8
J24208-3
Center support compressor (bar is also
Fig. 7-6, 7-14
used as gear pack support)
9
J24208-4
Snapring selection gage
Fig. 7-6
4-2
10
J24200
Collector ring installer and staker set
11
J24200-1
Collector ring staker
Fig. 6-34
4-3
12
J24200-2
Collector ring installer
Fig. 6-33
4-2
13
J24221
Fourth clutch alinement fixture
Fig. 7-34
4-2
14
J24210
Low and first clutch piston inner
Fig. 6-57
seal protector
4-2
15
J24216-01
Forward clutch piston inner seal protector
Fig. 6-36, 6-42
4-2
16
J24196
Main shaft lifting bracket
Fig. 7-14, 7-23
4-2
17
J24218-2
Stator roller holder
Fig. 6-9, 6-11
4-2
18
J24209
Fourth clutch lifting bracket
Fig. 5-32
4-2
19
J6125-1
Slide hammer (used with item 22)
Fig. 6-54
4-2
20
J24205
Bushing replacer set
21
J24205-1
Speedometer driven gear bushing installer
Fig. 6-55
22
J24205-2
Speedometer driven gear bushing remover
Fig. 6-54
4-2
23
J24219
Main pressure regulator and lockup valve
Fig. 6-16
spring compressor
4-3
24
J24171-2&4
Slide hammer
Fig. 6-49, 6-50
25
J24171-1
Dust shield remover
Fig. 6-49, 6-50
4-3
26
J24198
Oil pump oil seal installer (used with
Fig. 6-18
J24202-4)
4-3
27
J24202-1
Transmission rear oil seal installer
Fig. 6-60
(used with J24202-4)
4-3
28
J24202-4
Driver handle (used with items 26, 27,
Fig. 6-18, 6-60
59)
4-3
30
J24197
Front support needle bearing installer
Fig. 6-17
(used with J8092)
4-3
31
J24203
Output shaft bushing installer
Fig. 6-59, 7-54
4-3
32
J26282
Manual shaft oil seal installer
Fig. 6-62
4-3
33
J24217
Main shaft orifice installer
Fig. 6-47
4-3
34
J24369
Orifice plug installer
Fig. 6-58, 6-47
717
Back to Top
