TM-55-1425-289-14
CARRIER, AIR DEFENSE, MISSILE SYSTEM, XM1058 TRUCK TRANSPORTER; SHOP EQUIPMENT, GUIDED MISSILE SYSTEM; GUIDED MISSILE, AERIAL, XMIM-115 AND SHELTER CARRIER, TRUCK, CARGO, 2-1/2-TON, M35A2
TECHNICAL MANUAL; TRANSPORTABILITY GUIDANCE, ROLAND MISSILE SYSTEM AND ROLAND FIRE UNITS
SEPTEMBER 1985
TM-55-1425-289-14 - Page 29 of 61
TM 55-1425-289-14
in figure 5-1. The bill of materials for blocking and
tiedown of the XM1058 truck transporter is shown in
table 5-1. Data on the application of these materials are
provided in table 5-2.
b.
Fire Unit.
The palletized fire unit can be loaded
on a 12-ton, or larger, semitrailer as shown in figures 5-2
and 5-3. A bill of materials for blocking and tiedown of
the truck transporter is shown in table 5-3, and data on
the application of these materials, table 5-4.
Table 5-1. Bill of Materials for Blocking and Tiedown
of XM1058 Truck Transporter on Semitrailer
Approximate
Item
Description
Quantity
Lumber
Douglas-fir, or comparable;
straight-grain, free from material
defects; Fed Spec MM-L-751:
2- x 2-inch
6 linear ft
2- x 4-inch
66 linear ft
2- x 6-inch
22 linear ft
2- x 8-inch
48 linear ft
Nails
Common, steel, flathead, bright or
cement-coated, Fed Spec FF
N-105:
12d
172
20d
68
Wire Rope
6 x 19, IWRC; plain steel; pre
formed, regular-lay; Fed Spec RR
W-410: 1/2-inch
55 ft
Clips
U-bolt, Crosby heavy-duty, or
equal; Fed Spec FF-C-450, Type I,
Class 1: 1/2-inch
20 ft
Thimbles
Commercial grade; standard, 1/2
inch
4
Anti-
Neutral barrier material; water
chafing
proof or burlap; MIL-B-121, or
material
equal
as required
Table 5-2. Application of Materials for Blocking and
Tied own of XM1058 Truck Transporter on
Semitrailer
Item
No. Required
Application
1
8
Chock blocks. Locate beveled end of the
block against the wheel. Nail the first piece
to the trailer floor with five12d nails. Nail
each additional piece with four 20d nails.
2
2
Rubbing Strip, 2- x 6- x 36-inch. Position
on the edge of the chock block, and nail to
the lower piece (item 3) with five 12d nails.
3
2
Side blocks, 2- x 4- x 36-inch (tripled). Nail
the first piece to the trailer floor with five
12d nails. Nail each additional piece in a like
manner.
4
2
Rubbing strip, 2-inch x 6-inch + 8-foot 0-
inch. Nail to the lower piece (item 5) with
one 12d nail spaced every 8 inches.
5
2
Side blocks, 2-inch x 4-inch x 8-foot 0-inch
(tripled). Nail the first piece to the trailer
floor with one 12d nail spaced every 8
inches. Nail each additional piece in a like
manner
6
2
Wire rope, 1/2-inch-diameter, 11.5-ton. In
stall cable to the approximate angle shown
Table 5-2. Continued
Item
No.
Required
Application
6
(cont)
in figure to form a complete loop around the
lading rear mainframe member and to pass
through the trailer tiedown facility.
Cau-
tion
: Do not tie cable to lading lofting de
vices.
Note:
Cable of a larger size may be
used when specified cable is not available.
7
10
Clips, 1/2-inch-diameter. Four per cable and
one per thimble. See item 10.
8
2
Wire rope. 1/2-inch-diameter, 11.5-ton. In
stall cable to the approximate angle shown
in figure to form a complete loop around the
lading rear mainframe member and to pass
through the trailer tiedown facility.
Caution
: Do not tie to lading lifting devices.
Note: Cable of a larger size may be used
when specified cable is not available.
9
10
Clips, 1/2-inch-diameter; four per cable and
one per thimble. See item 10.
10
4
Thimbles, standard, 1/2-inch; one per trailer
tiedown facility. Secure to wire rope with
one clip per thimble.
Note
: A standard
thimble as specified can be secured to a cable
with a 1/2-inch clip. However, if desired, or
if the 1/2-inch thimble being used is of a type
that cannot be secured to a cable with a 1/2
inch clip, a 5/8-inch clip may be used. Note
that an "open pattern" thimble is recom--
mended.
11
Waterproof paper or burlap of sufficient size
to position under and extend 2 inches above
rubbing strips (items 2 and 4).
Table 5-3. Bill of Materials for Blocking and Tiedown
of ROLAND Fire Unit on Semitrailer
Approximate
Item
Description
Quantity
Chain
General service S-leg, high-tensile,
1/2-inch, 10-foot length, with two
grabhooks; 16,000-lb safe working
load.
4
Load
Type I, plain, 18-1/2-inch; operating
binder
s
lever, with two grabhooks designed
for 1/4- to 1/2-inch chain; 16,000-lb
safe working load. Fed Spec GGG-
B-325A; NSN 3990-00-171-9774
4
Table 5-4.
Application of Materials for Blocking and
Tiedown of ROLAND Fire Unit on Semitrailer
Item
No. Required
Application
NA
2
Chains. Secure a chain to each front tiedown
ring. Crisscross the chains, and attach the
ends of the chains to the trailer.
NA
2
Load binders. Tighten the front chains with
the load binders.
NA
2
Chains. At the aft end of the fire unit, attach
one end of each chain to the trailer. Pass the
chain over the top of the fire unit and in
back of the lofting fittings, and attach the
chains to the trailer.
NA
2
Load binders. Tighten the aft chains with
the load binders.
5-2
Back to Top
