TM-9-2320-209-34P
2½-TON, 6X6, M44A1 AND M44A2 SERIES TRUCKS (MULTIFUEL)
DIRECT AND GENERAL SUPPORT MAINTENANCE; REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS)
NOVEMBER 1989
CHANGE 2
TM-9-2320-209-34P - Page 13 of 908
TM 9-2320-209-34P
F
Reparable item. When uneconomically
reparable, condemn and dispose at the direct
support level.
H
Reparable item. When uneconomically
reparable, condemn and dispose at the general
support level.
D
Reparable item, When beyond lower level repair
capability, return to depot. Condemnation and
disposal not authorized below depot level.
L
Reparable item. Repair, condemnation, and
disposal not authorized below depot/specialized
repair activity level.
A
Item requires special handling or condemnation
procedures because of specific reasons (i.e.,
precious metal content, high dollar value,
critical material or hazardous material). Refer
to appropriate manuals/directives for specific
instructions.
c.
National Stock Number.
Indicates the National
stock number assigned to the item and will be used for
requisitioning purposes.
d.
Part Number.
Indicates the primary number
used by the manufacturer (individual, company, firm,
corporation, or Government activity), which controls the
design and characteristics of the item by means of its
engineering drawings, specifications standards, and
inspection requirements, to identify an item or range of
items.
NOTE:
When a stock numbered item is requisitioned, the
repair part received may have a different part number than
the part number than the part being replaced.
e.
Federal Supply Code for Manufacturer (FSCM).
The FSCM is a 5 digit numeric code listed in SB 708-42
which is used to identify the manufacturer, distributor, or
Government agency, etc.
f.
Description.
Indicates the Federal item name
and, if required, a minimum description to identify the
item. Items that are included in kits and sets are listed
below the name of the kit or set with the quantity of each
item in the kit or set indicated in the quantity incorporated
in unit column. When the part to be used differs between
serial numbers of the same model, the effective serial
numbers are shown as the last line of the description. In the
Special Tools List, the initial basis of issue (BOI) appears as
the last line in the entry for each special tool, TMDE, and
support equipment. When density of equipments supported
exceeds density spread indicated in the basis of issue, the
total authorization is increased accordingly.
g.
Unit of Measure (U/M).
Indicates the standard
of the basic quantity of the listed item as used in
performing the actual maintenance function. This meausre
is expressed by a two-character alphabetical abbreviation
(e.g., ea, in, pr, etc.). When the unit of measure differs from
the unit of issue, the lowest unit of issue that will satisfy
the required units of measure will be requisitioned.
h.
Quantity Incorporated in Unit.
Indicates the
quantity of the item used in the breakout shown on the
illustration figure, which is prepared for a functional group
or an assembly. A “V” appearing in this column in lieu of a
quantity indicates that no specific quantity is applicable,
(e.g., shims, spacers, etc.).
4.
Special Information.
a.
Usable on codes are shown in the description
column. Uncoded items are applicable to all models, unless
otherwise indicated by model application in the
description column, Identification of the usable on codes
used in this publication are:
Code
Used On
AA
All models equipped with gasoline engine
Model OA-331
AB
All models equipped with the multi-fuel LDS-
427-2 engine
AC
All models equipped with multi-fuel engines
LD-465-1, LD-465-1C or LDT-465-1 C
AD
All models equipped with front winch
AE
All models equipped with power takeoff
b.
References to the M44A2 series apply only to
the multifuel clean air engine (LDT 465-1 C, NSN 2815-00-
103-2642). Some figures include the words “clean air” in
parentheses to designate this.
c.
Detailed manufacturing instructions for items
source coded to be manufactured or fabricated are found
in TM 9-2320-209-20/1 (TM 9-2320-209-20, gasoline
models only) and TM 9-2320-209-34 (TM 9-2320-209-35,
gasoline models only). Bulk materials required to
manufacture items are listed in the Bulk Material Group
9501 of this manual.
d.
Detailed assembly instructions for items
source coded to be assembled are found in TM 9-2320-209-
20/1 (TM 9-2320-209-20, gasoline models only) and TM 9-
2320-209-34 (TM 9-2320-209-35, gasoline models only).
Assembly components are listed immediately following
the item to be assembled.
Repair parts kits and gasket sets appear as the
last entries in the repair parts listing for the figure in which
its parts are listed as repair parts.
Change
1
vii
Back to Top
