5.
Clear
any grease from the
outer nut and retaining washer in
order to inspect the washer tabs. At
least one tab of the washer shouLd
Be bent, either over a flat of the
6±
Take the hUb asseMbLy off
anD InspEct ±t ²nD ³He ´Ear±nGs FOr
DaµaGE (rEPair Or rePlace daµ¶G-
t
ED OnEs)·
7²
CarefulLY fi¸ the hUb on the'
axle,
secUriNg the adjUsting and
retaining nUts on the wh¹l with the
wasºer »ab¼
8³
½he point of it aL¾: ¿ÀÁÂ ÃÄÀ
½Å¿
OF
TÄÀ
RÀTAÆÁÆÁÇ
KÀV
WASÄÀR over a Flat of the Outer hex
nut or into a cutoUt of the ÈunÉ
Êouter ËUtÌ Íf your retaining washer
doEsnÎt have the tab locks, ask your
supply Ïople to get you one with
ÐÑÒÓs Listed in your trailer ½ÔÕsÌ
ReplaÖe the hubcap·
.
I
q
Redeye REpacking
'
:
´
There's an impo
r
Nt note slate
d
for
Table
3-1
of TM9-1400±²25±12 on
repacking the Redeye missiLe system.
Wha< it will say is that any unit or
team which removes the weapon from
its
·
styrofoam container and water³
proof barrier bag mUst rePlace it in a
sealed barrier bag beFre PUtting it
back in the Storage container.
´aras
4-
µ,
4-8
and µ±9 of TM 9¶
±400-425-35
tell yoU ho· to repacK
BUT ouR
rECeY G¶tS
REPLACeD
/N A
S!al±D
ba··I¸¹ ºag
,I
the weapon. Whoever Unpac sit mUst
repacK it. The seaLed bag is a mUst for
moistUre
protection
when
the
weapon's in the container.
How To GET
a
FasTENEr
¸¹ YoUºve reqUested tHe new stUD
¹Astener» ¼½¼
²³´µ-µ²-0¶²-·8¸³
or
²³¹µ-µ²-µ³º-·8¸»,
¾r
tHe
Battery
assemBLY O¹ YoUr ¿ÀW sYstem» ¹Árget
Ât Ã.
. at Least ÄÁr now.
»
ÅÂL tHe new one gets in tÆe sUPPLY
sYstem (Ât maY HÇve anotHer ¼½¼)»
yoU can maKe do witÈ sÉUD ¹AsteneÊ
¼½¼
¼·¸¼-µ0-³56-½879
anD
¼·6)µ²-
µ¸µ-·8¾·.
¿hE ¹Ârst ¼½¼
(-¿8À9Á
Has
been DeLeteD ¹Ëom tHe ÌMÍλ BUt
some are stÂLL ÇvaÂLÇBLeÏ
¸n case YoU ÐÂDnÑt get tHe worD»
rÒÓLacement ¹Ôr tÈe ¹Çsteners Âs now
organÂzationaL
LevEÕÖ ¸t UseD to Be
sUÓport»
BUt
T×
9-²´¸¼-³Âµ-óPÄ
•
droppeD it to
PAQZZÅ
\
2¼