TM-9-2320-362-14-P
TRUCK UTILITY: S250 SHELTER CARRIER, 4X4, M1037 FOR TRAFFIC JAM AN/TLQ-17A(V)3 (HMMWV)
TECHNICAL MANUAL; OPERATOR, UNIT, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST FOR ELECTRICAL ENVIRONMENTAL SYSTEM (EES)
APRIL 1992
TM-9-2320-362-14-P - Page 149 of 353
TM 9-2320-362-14&P
4-18. EES KIT INSTALLATION (Cent’d)
I
INITIAL SETUP:
Drill bit, # 21 (Item 4,
Section III, Appendix B)
Drill bit set (Item 3,
Section III, Appendix B)
Drill bit, 3/4-inch (Item 4,
Section III, Appendix B)
Electric drill (Item 3,
Section III, Appendix B)
General mechanics tool kit
(Item 1, Section III, Appendix B)
Arbor, hole saw (Item 12,
Section III, Appendix B)
Blade, hole saw (1-5/8”) (Item 9,
Section III, Appendix B)
Blade, hole saw (2-1/2”) (Item 11,
Section III, Appendix B)
Blade, hole saw (2-5/8”) (Item 10,
Section III, Appendix B)
Crowfoot (1-3/16”)
(Item 5, Section III, Appendix B)
q.Water pump pulley installation
. Sealing compound (Appendix C,
Item 7)
●
One water pump pulley P/N 12338782
t. 200 amp alternator mounting
brackets installation
One alternator adjusting bracket
P/N 12340057
●
Two capscrews P/N MS90728-60
(.375-16UNC-2Ax1.000 LG)
●
Two washers
P/N MS27183-13 (3/8 CAD)
One alternator bracket P/N 12338786
One hex bolt P/N 12340845-2
(M10-1.5X30mm)
●
One support bracket P/N 12342075
u. 200 amp alternator pulley
installation
●
One 200 amp alternator pulley
P/N 12339392
v. 200 amp alternator installation
Crowfoot (l-5/8”) ‘
-
●
(Item 6, Section III, Appendix B)
punch and die, knockout (1-3/4”)
(Item 8, Section III, Appendix B)
Socket wrench attac., hex, 6 mm,
3/8 drive (Item 13, Section III
●
Appendix B)
●
a. EES kit preparation
●
One EES kit template P/N C5136351
●
●
One insulation template P/N C5136348
●
●
Two grommets P/N MS35489-27
. One protector P/N 12339902-7
●
b. Tunnel interior side insulation
blanket and retainer installation
●
●
One insulation blanket
P/N 12339041
●
●
One insulation retainer
P/N 12339018-1
●
m. Fan drive assembly removal
●
One compressed air adapter
●
assembly (Appendix E)
One alternator fan guard assembly
P/N 12341809
●
Five washers
P/N MS51412-2 (#10 CAD)
●
Five hex head screws P/N 431942
One bolt P/N MS35764-854
(7/16-14x2.50GR8)
One hex head bolt
P/N MS35764-853 (7/16-14x2.00)
One lockwasher P/N MS35338-46
One screw P/NMS90728-60
(.375-16UNC-2Ax1.000 LG)
One spacer P/N 12338186-62
(.160 THICK)
One special stud
P/N 12339406-2 (M10x1.5x30)
One 200 amp alternator
P/N 12338796
Two lockwashers P/N MS35338-47
(3/8 CAD)
Two washers P/N 2436164
(7/16 CAD)
4-37
Back to Top
