TM-9-2330-238-14

CHASSIS, SEMITRAILER: 6-TON, 4-WHEEL M295A1; SEMITRAILER, VAN: EXPANSIBLE, 6-TON, 4-WHEEL M313; SEMITRAILER, VAN: SHOP, FOLDING SIDES, 6-TON, 4-WHEEL M447 AND M447C; SEMITRAILER, VAN: REPAIR PARTS, SHOP EQUIPMENT, 6-TON, 4-WHEEL M749; SEMITRAILER, VAN: REPAIR PARTS STORAGE, 6-TON, 4-WHEEL M750

TECHNICAL MANUAL; OPERATOR’S, ORGANIZATIONAL, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL

JULY 1992
TM-9-2330-238-14

  TM-9-2330-238-14 - Page 363 of 462

TM
9-2330-238-14
5-20.
RIGHT
REAR
DOOR
AND
SIDE
DOOR
LOCKS
REPLACEMENT
(M313,
EARLY
MODEL)
(Con’t).
4.
Remove
two screws
(13) and locking
bar grommets
(12) from door
(11).
5.
Remove
12 screws
(6) and three
latch assemblies
(7) from door
(11).
6.
Remove
four screws
(3) and door
case
assembly
(16) from door
(11).
7.
Remove
three screws
(10), outside
door
handle
(9), and gasket
(8) from door (11).
Discard
gasket.
WARNING
Dry cleaning
solvent,
P-D-680,
is toxic and flammable.
Always wear protective
goggles
and gloves,
and use only in a well-ventilated
area.
Avoid contact
with skin, eyes,
and
clothes,
and DO NOT breathe
vapors.
DO NOT use near open frame or excessive
heat.
The
solvent’s
flash
point
is 100°F-138°F
(38°C-59°C).
If you
become
dizzy
while
using cleaning
solvent,
immediately
get fresh air and medical
help. If solvent
contacts
eyes,
immediately
wash your eyes
and get medical
aid.
1.
Clean
all parts with dry cleaning
solvent
and dry thoroughly.
2.
Inspect
door
case
assembly
and latch assemblies
for ease
of operation.
3.
Inspect
locking
bars from
cracks,
bends,
or breaks.
Straighten
any minor
bends.
4.
Replace
any defective
parts.
1.
2.
3.
4.
5.
6.
7.
8.
Position
outside
door
handle
(9) and new gasket
(8) in place
on door (11)
and install
three
screws
(10).
Position
door
case
assembly
(16) in place
on inside
of door
(11) and install
four screws
(3).
Position
three
latch assemblies
(7) in place
on inside
of door (11)
and install
12 screws
(6).
Install two screws
(13) and locking
bar grommets
(12) on inside
of door
(11).
NOTE
For right rear door perform
step 5. For side door
go to step
6.
Position
upper
and lower door
locking
bars (5 and 14) on door case assembly (16)
and install two new cotter
pins
(15).
Position
upper
and lower
locking
bars (5 and 14) in place
on three latch assemblies
(7) and install
three new
cotter pins
(4).
Position
inside
door
handle
(2) in place
on shaft with holes alined
and install
headless
straight
pin (1).
Lubricate
door
case
assembly
(16) and
latch
assemblies
(7) in accordance
with
Lubrication
instructions
(Chapter
3, Section
I).
5-61


Back to Top