'
For a Good Seal .
..
If you've had problems with youR
OH-58 dooR Seals c±ming unglued,
heRe' Re some tips to keEp
.
' em in place:
²emoVe the RetaineRs and Rivets³
DiscaRd the old seal and ReMove the
old glu´³· Clean the aRea with a cloth
µa¶pened with toluene, and dRy with
a clean cloth³
¸leaN
a nw seal with a toluene¹
dampened cloth³ Use 80ºgRit sand»
pape¼ to Roughen the seal so the glue
will stick BetteR, and clean the seal
again with toluene³ DRy it with a clean
cloth½
3861,on the seal and dooRFRame½ Let it
dRy F¾R the time specifi¿d on the label³
ÀiRmly pRess the seal into plaÁe³ YoÂ
caà maintain pRessuRe f¾R an houR oR
so by closing the dooR on the seal³
AFteR the glue dRies, install
RetaineR cliPs with blindºtype Rivets³
40
Äo can get in a
ind, ÅÆÇ5È types,
when
É
RoÂTing a new gas pRoÊÂceË
caÌleÍ
·
Îo beFoËe yoÏ staËt, maKe sÂËe the
gËommets in Ðhe cÑbin RooF beam aËe
Ò
in good shaÓe and ÓËopeRlÔ seated in
the holes³
ÕeveË taKe Ðhe GRommets oÂt aÖd
thRow Ðhem away³ ×hat may maKe iÐ
easieR to pÂt the cable in bÂt it'll ËÏb
against the ØeÐal anÊ yoÂÙll soon ÚeeÊ
anotheR ReÓlacemenн
Coat
Ðhe
conÐRol
caÛle
with
petËoleÂm jelly ÌeF¾Re yo staRtÜ ×he
cable will slip ÐhËoÂgh Ðhe gRommets
Gas producer cable
Ý
easie˳ ÞeveË Âse
Ðoß mÂch FoËce
pÂshing on àthe cable oË yo may KinK
-_±
;:
±
-
²,
i³
´
µ¶·¸
¹
T
it³ ×hat'll give yo a sÐiFF coáÐËßl³ Îee
âaËa 4º92F oF ×ã ääº1äåæº228º23 FoR
Ðhe wßËÊ ßn maximÂm F¾Rce you
shßÂld neeÊ to ÐÏËn the contRol aFteR
insÐallation³
IF the conÐRol gets stiFF aFteR it's Ìçen
installed a while, check the boot, Item
3È in èig 4é1êë in Ðhe ì23 ×ã³
±
×he insiÊe oF Ðhe boot geÐs gÂmmy
FRqm engine cleaning solventí and can
cause paRtial binding oF the cable³ ×he
oÂÐside may look Åî so sQÏïeze the
Ìoot togeÐhe˳
IF the boot is sticðñ, clean the cable
with
MEK
and use
ò
a
new boot³