TM-1-1500-344-23-4

CONSUMABLE MATERIALS AND EQUIPMENT FOR AIRCRAFT AND AVIONICS VOLUME IV

TECHNICAL MANUAL; CLEANING AND CORROSION CONTROL

SEPTEMBER 2013
TM-1-1500-344-23-4

  TM-1-1500-344-23-4 - Page 9 of 92

2-1
NAVAIR 01-1A-509-4
TM 1-1500-344-23-4
01 September 2013
CHAPTER 2
CONSUMABLE MATERIALS FOR CORROSION CONTROL
2-1.
INTRODUCTION.
The materials referenced
in this chapter are approved for use, but approval
should not be misconstrued as an endorsement of any
manufacturer's product(s). If approved materials
for an
application/procedure are not available, contact your
service representative for approved substitutes: NAVAIR
North Island (Code 434), San Diego, CA (Navy), or the
AMCOM Corrosion Program OfFce, U.S. Army Aviation
Systems Command, Redstone Arsenal, Huntsville, AL
(Army).
2-2.
ARRANGEMENT OF CHAPTER.
Chapter 2 lists
consumable materials used for aircraft and avionics
cleaning and corrosion control.
2-2.1. Materials are grouped by function in the following
tables:
a. Table 2-1. Abrasives.
b. Table 2-2. Chemical Conversion Coating
Materials.
c.
Table 2-3. Cleaning Compounds.
d. Table 2-4. Cleaning Supplies.
e. Table 2-5. Corrosion Preventive Compounds.
f.
Table 2-6. Encapsulants.
g. Table 2-7. Lubricants.
h. Table 2-8. Neutralizing Agents.
i.
Table 2-9. Packaging/Protective Materials.
j.
Table 2-10. Paint Removers.
k.
Table 2-11. Paint Thinners.
l.
Table 2-12. Paints - Primers.
m. Table 2-13. Paints - Topcoats.
n. Table 2-14. Sealants.
o. Table 2-15. Solvents.
p. Table 2-16. Tags/Forms.
q. Table 2-17. Tapes.
r.
Table 2-18. Tracers/Indicators.
2-2.2. A description of the column headings and contents
is given below.
a. Nomenclature: the name of the material.
b.
SpeciFcation/Part Number: the military or industry
speciFcation and/or the commercial part number.
c.
National Stock Number: the
national stock
number of the material to be ordered.
d. Unit of Issue: the type/size of the material
container. Unit of issue abbreviations are shown below.
Only the most commonly used sizes are listed. Other
sizes may be available.
CODE
UNIT
CODE
UNIT
CODE
UNIT
BD
Bundle
DZ
Dozen
OZ
Ounce
BG
Bag
EA
Each
PG
Package
BO
Bolt
FT
Foot
PR
Pair
BT
Bottle
GL
Gallon
PT
Pint
BX
Box
GR
Gross
QT
Quart
CA
Cartridge
HD
Hundred
RO
Roll
CB
Carboy
JR
Jar
SE
Set
CN
Can
KT
Kit
SH
Sheet
CO
Container
LB
Pound
TU
Tube
CS
Case
LG
Length
YD
Yard
DR
Drum
MX
Thousand
-----
-----
e.
Intended Use: a short description of what the
material is used for.
f.
Usable On: an "x" in this column indicates that
the material has been approved for use on Aircraft (AC)
and/or Avionics (AV). If a material does not have an
"x", contact the cognizant engineering authority for the
speciFc aircraft/component for authorization before use.
2-3.
QUALIFIED PRODUCTS LIST
. The QualiFed
Products list (QPL) is a listing of products that have met
the requirements stated in the material speciFcation. ±or
material speciFcations with an associated QPL, only
qualiFed products shall be used. QPLs can be viewed in
the QualiFed Products Database section of the ASSIST
2-4.
PAINTS-TOPCOATS.
Only the most commonly
used topcoat colors have been assigned NSNs. Contact
NAVAIR North Island (Code 434) to establish NSNs for
new, ongoing program requirements. Other colors may
be procured directly from a qualiFed manufacturer listed
on the QPL. Minimum order quantities may be required
for specialty colors.


Back to Top