±
COMMUNIcATiONS
±²h
's
a PM tip or so on your AN/GRC-106
radIo set that'll keep your set out of the repair
shop and on the job where it belongs.
Like, when your set is tuned, but it's not load±
ing or operating properly after switching Fom
TU²E to OPERATE, take another look at your
tunIng procedure. ³t mIght be the b´ower protecµ
tion circuit has gone bad¶
But, be·re you head your Angry¸1¹6 toward
repair, switch baºk to TUNE, then back to
OPERATE» This might bring y¼ur set to nor½al
·
.
³¾ Y¿À're SÁIÂÂ hÃvIÄÅ a ÆroÇÂeÈ operÃtiÄÅ, ÃÄd
WHEl-
USlfG
an ±²R
Y¿Àr Æower sourÉÊ ¿r SuÆÆÂy IS
ËK, Ået yo
Ì
r re
Í
ho?e, K³´P tµ¶ ·¸r
ÆÃirÈÃÄ Áo ÅIve Y¿À Ã HaÄd.
p¹E5suº»
uNDER
3ÎÏÐÑÒ
Keep ÁHe AÓÔÕÕ49 radI¿ ÖeqÀeÄ×Y ØÈplIÙer
And Wear gO±²L³s.'
Öom gettiÄg overHeated Çy ÚeepiÄg Ãll ×ÂothIÄg
aÄd ¿tHer ÆersoÄal ÅeÃr oÛ tÜe ÝÞ aÈpÂIÙer. ßoÀ
als¿ Äeed to Úeep dÀst ÃÄd dirÁ ouÁ ¿¾ tHe AM-
ÕÕ49 Heat¸excHÃnger asseÈÇÂYà áÂeaÄ tHe ØSâ
sembly witH a low
Í
Æressure Ãir ãose.
AÄotHer wÃy t¿ Úeep
y¿ur setä c¿o is aÂways
keep your RT¸662 or ¸8Õ4
receiver¸transmItter and
AMåÕÕ49 together. Tãat
goes even when one of
these major components
needs to be turned in ·r
repair. æend them both to
support
ç
especiaÂÂy
when
adjustmeÄt
IS
needed.
Adjusting during a mismatch wiÂÂ cÃuse y¿Àr
dynèmic duo to overãeat wHen tHeY are back toµ
gethér again.
ßou also need to keep handles out o¾ the wêy
When you're not using them so tHey'll Ŀt get
banged and brokenë
ìhen you've put the CX¸í¹¹7í/U, aÄd CX¸
í¹¹99/U ×ables on your A² /îRC¸í¹6, lock them
oÄ and pusã the lock handles out of the way.
A¾ter you have A² T TU²E and A² T ïËAD
settingS where you want them, ðld the kÄob
ñ
HaÄdles inò
And, when you turn the O² -OÞÞ switch on
the AM¸ÕÕ49, save the muscle» All it takes is a
tou×h ¿f the óngers to turn it one way or the
otherô
Put the ÝT in æTA² DBß ·r 2 minutes beõ
·re shutting if oö¶
49