DMWR-9-2815-220
AVDS-1790 ENGINE OVERHAUL STANDARD
DEPOT MAINTENANCE WORK REQUIREMENT
DMWR-9-2815-220 - Page 112 of 1422
. -·±
.±²
.
-·t± ² ,³´µ
³´ ,µ ¶·
.
¸¹
¶
¸¹ º
²
³
:
´_µ¶
¸¹º
»
2¼
½¾¿
·
5-3.
(Cont)
». ¼
½
_
¾¿ _
À
DMR 9-2815±220
(3)
B
out all tApped hoLes with comPressed AiR.
(4)
r cLeaNing, dry cAsti±g with coMpRessed Air²
·c.
OiL ³´ssages.
±1²
µ
e
AN PassAges witH wire oR Probes to bReAk Up ALl s¶Udge or guM deposits.
³2´
WSH PassAges by fl¸shing witH dry c¹eANiNg solve±tº »¼-D½680º TyPe I¾¿À
Be sUre pAs Á´ges ARe free froM obstrUctio±s aNd reMove Any particLes whicH Might
later beco dÃsLodged And coNtaMi±Ate tHe oil systeM
•
º
(3)
r cleA±iNgº
dry PassAges with coMpressed airÀ
dÄ
ElecÅÆÃcAl CAbles a±d FlexiÇle ÈosesÉ
CleA± cAbles a±d fÊexible Hoses with
soAP aNd wAËÌr²
Do not Allow dry clea±Ã±g soLve±t to be iN Prolo±ged contact witH
tHe rÍbbeR ÎÏMPoneNts and flexible Hoses to avoid MAKing theM ÍnserviceabLe.
"
eÐ
ÑAll
Ò
Ónd Ôeedle ÑeArings ²
(µ)
Õri±gs Req¸ire special atte±tioN i± cleANÃNg a±d oiLi±gÄ
Öfter Remov×
ñg sÍRface Øirt, oÃL oR greAse, the ÇeariNgs, except the sealed, Perma±e±tly
lÍÇÙicated ÅJpeÚ sHo¸ld be plAced ñ hot oil ÛAÇo¸t
µ5QOF)
to LooseN co±geaLed oil
a±d greAse Ä
Ü
ÝÖfter cLea±Ã±gÞ the beaRñgs shoULd be wrApped tigHtly ÃN oÃled oR
waxed pApeR ßNtil iNsPectio± a±d Assembly.
D
±ot ÃàRse sealed type ÇAll ÇeAriNgs
iá âry cLeA±ãNg solveát or Hot oiL²
E±tRa±ce of cLeA±Ã±g Age±t wiLl destRoy
L¸bricA±ts äAled iN ÇeARiNg At time of ma±¸fAct¸ReÉ
¶·¸
åæçAN seALed bAll beariNgs Çy wiPñg the exteRÃoR s¸rfaces wÃtH A cLeAN
clotH moÃstened ÃN dRy cleA±i±g soLve±tº »èéêëì80, íype ¾I¿À
îo Not ¸se coMpRessed
Air ÃN cLeANãNg oR dRyñg of ÇALL oR NeedLe ÇeAri±gs.
DAMage to ÇeaRi±gs wiLl
resïLt fRom ðpiNNÃNg of beAri±g by AÃR blastñ
¹3º
òeóeR to ôõ
²³´µ4
foR iNfoöatio± on ñs PectÃoN, cAre, A±d MAi±teNaNce of
beaÙi±gs.
»
fÀ
èain÷d èarts .
íHe reco±ditioNñg of painted Parts sHoÍld be a MAtteR of
gooø jÍdgMenË. ¼arts tHAt aPPear to be in good co±ditio± Afteù clea±i±gº need not
be útriPPed ûnd repAi±ted in tHeiR entÃretyº ÇUt sHoÍld be clea±ed and desig±ated
for toUch UPüonlyÀ èarts thAt Are rUsted, oR otHeýise devoid of paintÞ M¸st Çe
strþPped to bAre ÿtALÀ ĀÍÇbeR compositioN sHroÍd seals M¸st Çe reMoved aNd dÃsā
cArøed befoĂ the pArts cAá be striPped of PAÃntă
5»4¼
ĄNs pecËÃoáÀ
a.
Ge±eRaL.
ôhe eNgines
covered iN ąhÃĆ Dõćò aRĈ pRec1sĉĊN bċÃlt wÃth
Č
točé
ÁÂ
eRaĎces fÃxeď At extRemely cLos e LÃMitsÄ
Đey letters are Ísed in the overHAUL
ñsđectÃo± PĒocedures »ēĔ¼'s¿ to Locate poñts of measURemeNt for oveRHAUL limÃts .
½
EAcĕ secĖÃoN foLloėÃNg Ãá this
chApteR iácLÍdes O¾¼Ęs foR crÃtÃcal paRts
ę
oR compoë
)
±e±Ěs
coveReě ÃN the sectÃo±À
Ĝ¾¼ refeRe±ces foR s¸ch pARts or compoNe±ts ARe iáë
cL¸ĝed iN the weAR LÃmÃtsº
fits, A±d toLeraNces taÇLe.
ćhere aá Ĝ¾¼ is RefereNced
Ğá ğore ĠHAN oNe sectÃoN »eÄgÄġ the sAme PaRt Ãs ¸sed oN several s¸ÇasseMÇLÃes¿º
¶/´
Back to Top
