TM-55-1425-289-14
CARRIER, AIR DEFENSE, MISSILE SYSTEM, XM1058 TRUCK TRANSPORTER; SHOP EQUIPMENT, GUIDED MISSILE SYSTEM; GUIDED MISSILE, AERIAL, XMIM-115 AND SHELTER CARRIER, TRUCK, CARGO, 2-1/2-TON, M35A2
TECHNICAL MANUAL; TRANSPORTABILITY GUIDANCE, ROLAND MISSILE SYSTEM AND ROLAND FIRE UNITS
SEPTEMBER 1985
TM-55-1425-289-14 - Page 43 of 61
TM 55-1425-289-14
Figure 6-8.
Blocking and tiedown ofM35 truck, with OMTS shelter, in general cargo vessel.
Table 6-2.
Bill of Materials for Blocking and
Tiedown of ROLAND Fire Unit in Hold of General
Cargo Vessel (Fig.
6-6)
Item
No. Required
Application
A
2
Side blocks, lumber, 4-inch x 6-inch x
length-to-suit.
Locate against the fire unit
pallet, one piece on each side of the fire unit.
B
2
End blocks. Each consists of one piece of 4-
inch x 6-inch x length-to-suit lumber. Lo-
cate on top of side blocking and pallet edge.
Toenail to side blocking with four 60d nails
at each end.
C
as required
Bracing, lumber 4-inch x 6-inch x length-
to-suit.
Brace as required against fire unit
blocking, on the side of the vessel or adja-
cent to cargo blocking, to immobilize equip-
ment.
Toenail each end to adjacent bracing
with four 60d nails.
D
4
Padeyes. Required on the floor of the vessel
if proper D-rings or deck tiedown fittings
are not available.
E
2
Wire rope, 5/8-inch, formed into a complete
loop.
Secure with clamps (item H below). At-
tach to the front tiedown ring on each side
of the fire unit.
F
4
Turnbuckles, 3/4- x 18-inch. Apply between
wire rope and padeyes.
Tighten to even ten-
sion between all turnbuckles.
G
2
Wire rope, 5/8-inch; form the first cable into
a complete loop between the rear right-hand
gold club clevis, routed through cable guides
at the top corner, and the left-hand padeye;
form the second cable into a loop between
the left-hand golf club clevis, routed through
cable guides at the top corner, and the right-
hand padeye.
Secure each with four clamps
(item H below).
H
16
Clamps, 5/8-inch. Secure to items E and G
above.
Table 6-3.
Bill of Materials for Blocking and
Tiedown of XM1 058 Truck Transporter with Fire
Unit in Hold of General Cargo Vessel (Fig 6- 7)
Approximate
Item
Description
Quantity
Lumber
Douglas-fir, or comparable;
straight-grain, free from material
defects; Fed Spec MM-L-751: 4- x
6-inch
120 linear ft
Nails
Common steel; flathead; bright or
cement-coated; Fed Spec
FF-N-105: 60d
110
Wire rope
6 x 19, IWRC; improved
plow
steel; preformed, regular-lay; Fed
Spec RR-W-410: 5/8-inch
150 ft
Clamps
Wire rope, U-bolt clips, saddled,
single-grip; steel; Crosby heavy-
duty, or equal; MIL-STD-16842:
5/8-inch
32
Thimbles
Standard, open-type: 5/8-inch
14
Turn-
buckles
3/4- x 18-inch
8
Padeyes
Local manufacturer; 1-inch steel
rod and 4- x 6- x 5/8-inch steel
plate. Bore 1-inch holes through the
plate, and weld U-shaped 1-inch rod
ends to the top and bottom of the
plate.
8
Table 6-4.
Application of Materials for Blocking and
Tiedown of XM1058 Truck with Fire Unit in Hold of
General Cargo Vessel (Fig 6-7).
Item
No. Required
Application
as required
Side blocks, lumber, 4- x 6-inch x length-to-
A
suit. Locate against vehicle treads, one piece
on each side of vehicle.
6-8
Back to Top
