TM-9-2320-280-20-2

TRUCK, UTILITY: M998 SERIES

TECHNICAL MANUAL; UNIT MAINTENANCE; VOLUME 2 OF 3

JANUARY 1996
TM-9-2320-280-20-2

  TM-9-2320-280-20-2 - Page 773 of 951

7-24.
LEFT PARKING BRAKE CABLE/MOUNTING BRACKET REPLACEMENT
This task covers:
a. Removal
b. Installation
INITIAL SETUP:
Tools
General mechanic’s tool kit:
automotive (Appendix B, Item 1)
Materials/Parts
Assembled locknut (Appendix G, Item 130)
Two lockwashers (Appendix G, Item 135)
Cotter pin (Appendix G, Item 12)
Two retaining rings (Appendix G, Item 231)
Two locknuts (Appendix G, Item 71)
Manual References
TM 9-2320-280-10
TM 9-2320-280-24P
Equipment Condition
• Muffler and insulator removed (all models
except
M1123 and “A2” vehicles) (para. 3-48).
• Muffler and catalytic converter removed
(M1123 and “A2” vehicles only) (para. 3-49).
• Wheels chocked and parking brake released
(TM 9-2320-280-10).
TM 9-2320-280-20-2
7-58
Change 3
NOTE
• The following procedure applies to vehicles with serial numbers
USBL Eff. 44825 and above.
• If cables are chafing or crushed, use new cable clamp bracket.
1.
Remove cotter pin (11), washer (12), clevis pin (14), and brake clevis (13) from rear caliper lever (10).
Discard cotter pin (11).
2.
Remove brake cable retaining ring (9) and parking brake cable sleeve (2) from rear caliper cable
bracket (8). Discard cable retaining ring (9).
3.
Slide parking brake cable (1) through parking brake cable assembly (15). Remove parking brake
cable retaining ring (24) and parking brake cable sleeve (2) from “C” beam (22). Disconnect parking
brake cable (1) from parking brake equalizer bar (23). Discard cable retaining ring (24).
4.
Remove capscrew (6), washer (4), and assembled locknut (3) from brake cable clamp (5), mounting
bracket (21) and parking brake cable assembly (15). Discard assembled locknut (3).
NOTE
Perform steps 5 and 6 for vehicles with old parking brake cable
bracket. Perform steps 7 through 9 for vehicles with new parking
brake cable bracket configuration.
5.
Remove capscrew (17), lockwasher (16), parking brake cable clamp (18), and parking brake cable
assembly (15) from bracket (19). Discard lockwasher (16).
6.
Remove two capscrews (20) and bracket (19) from support bracket (7). Discard bracket (19).
7.
Remove locknut (36), capscrew (34), washer (33), and parking brake cable clamp (32) from
bracket (28). Discard locknut (36).
8.
Remove capscrew (31), lockwasher (30), and parking brake cable clamp (29) from bracket (28).
Discard lockwasher (30).
NOTE
Perform step 9 if clamp bracket is damaged. If not replacing
bracket, proceed to b., installation.
9.
Remove locknut (26), washer (27), capscrew (35), washer (25), and clamp bracket (28) from support
bracket (7). Discard locknut (26).
NOTE
Perform step 10 if replacing parking cable mounting bracket. If not
replacing bracket, proceed to b., installation.
10.
Remove two nuts (37), washers (39), capscrews (40), washers (39), mounting bracket (21), and
tailpipe hanger (41) from rear body mount (42).
a. Removal


Back to Top