TM-9-2320-361-34
2-1/2-TON, 6x6, M44A2 SERIES TRUCKS (MULTIFUEL)
TECHNICAL MANUAL; DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
MAY 1992
TM-9-2320-361-34 - Page 633 of 764
TM 9-2320-361-34
16-16.
POWER DIVIDER REPAIR (M764) (Contd)
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
16-90
Install dial indicator on housing (1) and position plunger on end of input shaft (2).
Measure and record end play by pulling input shaft (2) back and forth. Proper end play reading is
0.0001-0.005 in. (0.00254-0.127 mm).
NOTE
If end play is correct, go to step 40. If end play is incorrect, go to
step 35.
Remove dial indicator, four screws (12), lockwashers (11), and cap (10) from input shaft (2) and
housing (1). Discard lockwashers (11).
If end play is greater than 0.005 in. (0.127 mm), remove a shim (9) or use a thinner shim (9).
If end play is less than 0.0001 in. (0.00254 mm), add a shim (9) or use a thicker shim (9).
Install cap (10) on housing (1) with four new lockwashers (11) and screws
(12).
Perform steps 33 and 34. Perform procedure until correct end play is achieved.
Reposition dial indicator on housing (1) so that plunger is positioned on the end of output shaft (3).
Measure and record end play by pulling output shaft (3) back and forth. Proper end play reading is
0.0001-0.005 in. (0.00254-0.127 mm).
NOTE
If end play is correct, go to step 47. If end play is incorrect, go to
step 42.
Remove dial indicator, four screws (7), lockwashers (8), and cap (6) from housing (1) and output
shaft (3). Discard lockwashers (8).
If end play is greater than 0.005 in. (0.127 mm), remove a shim (5) or use a thinner shim (5).
If end play is less than 0.0001 in. (0.00254 mm), add a shim (5) or use a thicker shim (5).
Install cap (6) on housing
(1)
with four new lockwashers (8) and screws (7).
Perform steps 40 and 41.
Reposition dial indicator on housing (1) so that plunger is positioned on the end of shoulder shaft (4).
Measure end play by pulling shoulder shaft (4) back and forth. Proper end play reading is
0.0001-0.005 in. (0.00254-0.127 mm).
NOTE
If end play is correct, go to step 54. If end play is incorrect, go to
step 49.
Remove dial indicator, four screws (5), lockwashers (6), and cap (13) from housing (1) and shoulder
shaft (4). Discard lockwashers (6).
If end play is greater than 0.005 in. (0.127 mm), remove a shim (7) or use a thinner shim (7).
If end play is less than 0.0001 in. (0.00254 mm), add a shim or use a thicker shim (7).
Install cap (13) on housing (1) with four new lockwashers (6) and screws (5).
Perform steps 47 and 48. Perform procedure until correct end play is achieved.
Install new woodruff key (20) and sprocket (19) on shoulder shaft (4) with washer
new cotter pin (21).
(18),
nut
17), and
Back to Top
