TM-9-2330-356-14
SEMITRAILER, TANK: 5000 GALLON, BULK HAUL, SELF LOAD/UNLOAD M967 AND M967A1; SEMITRAILER, TANK: 5000 GALLON, FUEL DISPENSING, AUTOMOTIVE M969 AND M969A1; SEMITRAILER, TANK: 5000 GALLON, FUEL DISPENSING, UNDER/OVERWING AIRCRAFT M970 AND M970A1
TECHNICAL MANUAL; OPERATOR’S, UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL
OCTOBER 1990
TM-9-2330-356-14 - Page 440 of 528
TM 9-2330-356-14
c.
Cleaning, Inspection, and Repair.
WARNING
Dry cleaning solvent P-D-680 Is toxic and
flammable. Always wear protective goggles
and gloves, and use only in a well-ventilated
area. Avoid contact with skin, eyes, and
clothes, and DO NOT breathe vapors. DO
NOT use near open flame or excessive heat.
The solvent’s flash point is 100°F-138°F
(38°C-59°C). If you become dizzy while
using cleaning solvent, immediately get fresh
air and medical help. If solvent contacts eyes,
immediately wash your eyes with water and
get medical aid.
(1) Clean metal parts with dry cleaning solvent
(item 11, Appendix E) and dry thoroughly.
(2) Inspect gears for worn, damaged, or missing
teeth. Replace gears if damaged.
d.
Assembly (Fig.
8-6).
(1) Assembly
of Frame.
(a)
Position one side angle (74) onto the two
frames (6 and 15). Secure in place with four capscrews
(73), lockwashers (70), and nuts (71),
(b)
Install other side angle (74) onto the two
frames (6 and 15). Secure in place with four capscrews
(73), lockwashers (70), and nuts (71).
(c)
Install both tie rods (72) onto the frames
(6 and 15). Secure with four capscrews (68), washers (69),
lockwashers (70), and nuts (71).
(2)
Installation of Terminal Board in Motor
Junction Box (Fig. 8-7).
(a)
Install the two nuts (2, fig. 8-7) on studs
(1) on the terminal board (3). Install the middle capscrew
(4) and one nut (5) onto the terminal board.
(b)
Position the terminal in the motor
junction box (6). Install screw (7) but do not tighten. Install
capacitors (8 and 9) onto screw (7). Be sure capacitors are
installed with marking in position shown in figure 8-7.
Tighten screw (7).
(c)
Install lead with terminal (11) from
motor, along with capacitor lead, to terminal board.
Secure with screw (10). Install motor lead with terminal
(11) and capacitor lead to screw (4). Install second nut (5)
and tighten.
(d)
Reconnect
junction box (para 4-27).
hose reel wiring in motor
(e)
Replace motor junction box cover (55,
fig. 8-6) and secure in place with four machine screws (54).
Figure
8-7.
Terminal Board Installation.
(3) Installation of Motor (Fig. 8-6).
NOTE
Be sure pinion gear teeth mesh properly with
the ring gear teeth.
(a)
Install pinion gear (64) on motor shaft.
Tighten set screw (63).
- -
(b)
Position motor between mounting
bracket (62) and frame (6). Install four capscrews (59),
lockwashers (60), and nuts (61).
(c)
Install bushing (58) into junction box
(57). Install assembly onto motor.
(d)
Connect the two motor leads to the
terminal board (65) in the junction box. Connect leads to
terminal board and install conduit (para 4-27). Replace
cover (55) and secure with four machine screws (54).
8-10
Back to Top
