TM-9-2330-356-14

SEMITRAILER, TANK: 5000 GALLON, BULK HAUL, SELF LOAD/UNLOAD M967 AND M967A1; SEMITRAILER, TANK: 5000 GALLON, FUEL DISPENSING, AUTOMOTIVE M969 AND M969A1; SEMITRAILER, TANK: 5000 GALLON, FUEL DISPENSING, UNDER/OVERWING AIRCRAFT M970 AND M970A1

TECHNICAL MANUAL; OPERATOR’S, UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL

OCTOBER 1990

  TM-9-2330-356-14 - Page 442 of 528

TM 9-2330-356-14
(k)
Remove six screws (44) and lockwashers
(45) securing the ring gear (46) to the disc (47). Remove six
spacers (48) and ring gear (46). Remove six capscrews (49)
and shakeproof washers (50), and remove bevel gear (51),
(2)
Removal of Motor.
NOTE
Hose reel need not be removed from cabinet
to remove motor.
(a)
Remove four machine screws (52) and
then remove cover (53). Tag and disconnect electrical
leads from motor (54) at the motor junction box (55) and
remove all conduit connections (para 4-27). Disconnect
the motor junction box from bushing (56) and bushing
from motor.
WARNING
Do not remove nipple from motor. Nipple is
packed in place with plaster. if nipple is
removed, motor will no longer be explosion
proof. Failure to follow this warning may
result in serious injury or death to personnel.
(b)
Remove four screws (57), lockwashers
(58), and nuts (59) securing motor (54) to mounting
bracket (60) and to frame (6). Remove motor (54).
(c)
Loosen set screw (61) and remove pinion
gear (62).
(3)
Removal of Terminal Board in Motor Junction
Box.
(a) If
motor was not previously removed
under paragraph (2) above, remove the four machine
screws (52) and cover (53). Remove two leads with
terminals (11, fig. 8-7) that come from motor at the
terminal board. Tag and disconnect all electrical leads
from the terminal board (63) (para 4-27). Remove the two
capacitors (64).
(b)
Remove the two machine screws (65)
securing the terminal board (63) to the junction box and
remove the terminal board.
(4)
Disassembly of Frame.
NOTE
Drum and motor must be removed before
complete disassembly of frame can be
accomplished.
(a)
Remove four capscrews (66), washers
(67), lockwashers (68), and nuts (69). Remove two tie rods
(70).
(b)
Remove eight capscrews (71),
lockwashers (68), and nuts (69). Remove two side angles
(72).
Legend for figure 8-8:
1. Capscrew (2)
2. Lockwasher (2)
3. Flatwasher (2)
4. Pinion guard
5. Pinion bearing assembly
6. Front frame
7. Capscrew (2)
8. Flatwasher (2)
9. Lockwasher (2)
10. Nut (2)
11. Capscrew (2)
12. Flatwasher (2)
13. Lockwasher (2)
14. Nut (2)
15. Rear frame
16. Spacer
17. Bearing and collar
18. Stud (4)
19. Set screw
20. Disc
21. Capscrew (6)
22. Lockwasher (6)
23. Nut (6)
24. Collar
25. Thrust washer (as req’d)
26. Drum
27. Stud (4)
28. Spacer (4)
29. Adapter elbow
30. Swing joint
31. Capscrew
32. Lockwasher
33. Nut
34. Axle shaft
35. Capscrew (4)
36. Lockwasher (4)
37. Outlet elbow
38. O-ring
39. Set screw
40. Support collar
41. Capscrew (6)
42. Nut (6)
43. Lockwashers (6)
44. Screw (6)
45. Lockwasher (6)
46. Ring gear
47. Disc
48. Spacer (6)
49. Screw (6)
50. Shakeproof washers (6)
51. Bevel gear
52. Machine screw (4)
53. Cover
54. Motor
55. Motor junction box
56. Bushing
57, Screw (4)
58. Lockwasher (4)
59. Nut (4)
60. Mounting bracket
61. Set screw
62. Pinion gear
63. Terminal board
64. Capacitor (2)
65. Machine screw (2)
66. Capscrew (4)
67. Washer (4)
68. Lockwasher (12)
69. Nut (4)
70. Tie rod (2)
71. Capscrew (8)
72. Side angle (2)
73. Nut (6)
74. Lockwasher (6)
75. Nut (6)
76. Lockwasher (6)
8-12


Back to Top