TM-9-2815-200-35
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED ,12 - CYLINDER , ASSEMBLY ;MODELS AVDS-1790-2M (2815-856-4996), AVDS-1790-2A AND AVDS-1790-2AM (2815-856-9005)
TECHNICAL MANUAL; DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
TM-9-2815-200-35 - Page 539 of 779
a. Cylinder Head Plates, Oil Filler Tube, and
Oil Level Indicator Tube.
Refer to figures 5-60
through 5-51.
b.
Rear Shrouds.
Refer to figures 5-50
through 5-48.
c.
Front Shrouds.
Refer to figures 5-47
through 5-42.
d .
Throttle Linkage,
Fuel Drain Tubes ,
Fuel / Water Separator, Secondary Fuel Filter,
and Primary Fuel Filter.
Refer to figures 5-41
through 5-39, 4-84, 4-85, 5-38 through 5-34.
7-15.
Intake Manifold Assemblies, Cylinder Head Oil Drain Lines, and
Manifold Heater Tubes, Solenoids, and Filter
Refer to Table 7-11 for illustrations and assembly instructions. References are listed in
the table,
Table 7-11. Intake Manifold Assemblies, Cylinder Head Oil Drain Lines,
and Manifold Heater Tubes, Solenoids, and Filter
Component
References
Intake Manifold, Manifold Heater, and Turbosupercharger
Para 7-15a, Fig. 5-33
Air Outlet Elbow
Cylinder Head Oil Drain Tubes
Para 7-15b, Figs. 5-32 through 5-28
Manifold Heater Tubes, Hoses, Fuel Check Valve, Fuel
Para 7-15c, Figs. 5-27 through 5-23
Filter, Filter Bracket, and Solenoid Valves
a. Intake Manifold, Manifold Heater, and
elbow opening to prevent entrance of foreign
Turbosupercharger.
Refer to figure 5-28 and (1)
objects.
and (2), below.
b. Cylinder Head Oil Drain Tubes.
Refer to
(1) After tubes for cylinder Nos. 3R and 4R
figures 5-32 through 5-28.
are secured, tighten tube flange nuts at cylinder
c.
Manifold Heater Tubes, Hoses, Fuel Check
Nos. lR, 2R, 5R, and 6R at intake manifold.
Valve, Fuel Filter, Filter Bracket and Solenoid
(2) Cover turbosupercharger air outle t
Valves.
Refer to figures 5-27 through 5-23.
7-16. Oil Coolers, Beams, Cooling Fans, Shrouding, and Associated Parts
Refer to Table 7-12 for illustrations and assembly instructions. References are listed in
the table.
Table 7-12. Oil Coolers, Beams, Cooling Fans, Shrouding
and Associated Parts
Component
References
Turbosupercharger Oil Inlet Hoee and Transmission
Para 7-16a, Fig. 5-22
Shrouds
Oil Coolers, Support Beams, Upper Cover Frame, and
Para 7-16b, Figs. 5-21 through 5-7
Frame Support Bracket
Cooling Fan Shroud and Upper Covers
Para 7-16c, Figs. 4-141 through 4-136, 5-9 through 5-7, 4-
132 through 4-128
Cooling Fan Vanes and Cooling Fane
Para 7-16d, Fige. 4-35, 4-34, 4-88
a. Turbosupercharger Oil Inlet Hose an d
c. Cooling Fan Shroud and Upper Covers.
Transmission Shrouds.
Refer to figure 5-22.
Refer to figures 4-141 through 4-136, figures 5-9
b. Oil Coolers, Support Beams, Upper Cover
through 5-7, and figures 4-132 through 4-128.
Frame, and Frame Support Bracket.
Refer to
figures 5-21 through 5-7 and figure 7-34.
7-27
Back to Top
