TM-9-2815-220-34
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED, 12-CYLINDER, ASSEMBLY; MODELS AVDS-1790-2C (2815-00-410-1203) AND AVDS-1790-2D (2815-00-410-1204)
TECHNICAL MANUAL; DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL
TM-9-2815-220-34 - Page 168 of 532
TM 9-2815-220±34
I
Figure
2-137.
Re1±²q³´µIµG o¶ ·±¸stOlL·¹ºg STa»¼e½ cOble ±¾¿0µÀÁº¼ÂøG
b¶aCke¼, eAÄy enG·neÅ.
F
Â
g
ur
e
±²³´8µ
Remo1±ing or IMtalliNG fel AOlenu²d ³nD feL
&´µUt<F co¶·ECTo¸.
2·86.2
Change ²
¹º»¼¸E
±²¶´9·
Re½¾v¿ng OÀ In3ÁÂÃÄiÅ1g /e´ÆwÇÈE¸ ÉepaÊËÌoÍ ÎÏblE
ÐoÑneÒtOÊÓ
('1) Remove two capscrews and lOckwashers
±fig. 2-²39) and remove two L³p CLamps´ µut tie¶wrap
and remove fUeL/water separator cabLe CoNneCtor·
Remove capsCrew and LOCKwasher and remove L³p
CLamp¸ Remove CapsCrew and Lo¹kwasHer and remove
Bracketº
(i)
»Emove two capscrews, LO¼½washers and
hexagon nUts (²¾ fig¿ 2¶²40) and remove two l³p
Clamps ±2)À Remove two caps¼rews and LOCÁwashers
±3) and remove two ÂraCKets (Ã)Ä Remove two CapÅ
sCrews and LOCÆWasÇers
±5²
and remove two l³p
CLamps (6)Ä Remove ÇoUr meter CabLe Connector
³7´
and seLf-LÈking nut ±8) and remove lOop cLamp ±9)É
Remove Çigh oiL temperatÊre switCh CaÂLe eLeCtrical
ConneCtor sheLL ±²Ë)Ì oiL pressUre transmitter CaBLe
eLeCtriCal Connector sheLL (Ͳ), oiL temperatUre transÎ
mItter cabLe eLeCtrIcaL conneCtor shelL (Ï2), and Low
oiÐ pressUre CaBLe eLectrIcaL ConneCtor sheLL ±²3)·
µ¶
Remove two generator wIring harness caÂLe
connectors
·1
and 2Ñ fIgÀ 2¶Ï4²)Ä Remove Four maChine
sCrews, LÈkwashers and heXagon nUTS Ò3) and remove
transmIssion disConneCt caÂle conneCtor ÓÃ)Ä Remove
self ¶LÈking nUt and fLat washer
¸5¹
and remove
assembled BuSS bar and gEn±ratoR ca²l³ (6). INsTaJJ
fLaT washer And selF-loCkinG nUt´ µemove Sel¶·
L
o
c
½iÔg nUÕ
anD ¸aT waSHer
º»¼
and d¹SºOnn³ºt
aSSemBled BuSS b»r and gr¼und strap (8)½ ¾n¿Tall
selÀÁj¼ºK¹n nUT aNd ¸at waSÃerÄ ÅemOV± capScr³w
aÆd ¶lat WasÇer È9) aNd reM¼V³ asSemBled
ÖUS×
bar
aÉd GrOund STraP Ê8ËÄ
Back to Top
