TM-9-2815-200-35
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED ,12 - CYLINDER , ASSEMBLY ;MODELS AVDS-1790-2M (2815-856-4996), AVDS-1790-2A AND AVDS-1790-2AM (2815-856-9005)
TECHNICAL MANUAL; DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
TM-9-2815-200-35 - Page 12 of 779
Figure
Number
Title
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
4-42
4-43
4-44
4-45
4-46
4-47
4-48
4-49
4-50
4-51
Loosening or tightening oil filler upper and lower tube hose connection
(relocated oil filler tube installation ).
Removing or installing upper oil filler tube (relocated oil filler tube in-
stallation ).
Removing or installing crankcase rear breather tube and lower left rear
shroud plate.
Removing or installing upper oil filler tube support bracket and tur-
bosupercharger end shroud.
Disconnecting or connecting turbosupercharger oil inlet hose elbow from
nipple using open end wrench-5120-448-0404.
Removing or installing turbosupercharger outer shroud plate.
Removing or installing oil inlet hose, elbow, and nipple.
Removing or installing generator exhaust tube cap (right side only).
Removing or installing generator exhaust tube support clamp (right side
only).
Removing or installing generator exhaust tube (right side only).
Disconnecting or connecting inner shroud plate (rear view).
Removing or installing transmission oil cooler end shroud and inner shroud
plate.
Disconnecting or connecting turbosupercharger oil drain tube at tur-
bosupercharger.
Disconnecting or connecting turbosupercharger air outlet elbow.
Disconnecting or connecting turbosupercharger at mounting base.
Disconnecting or connecting exhaust pipes at turbine housing and removing
or installing turbosupercharger.
Removing or installing cooling fan vanes.
Removing or installing cooling fans.
Disconnecting or connecting front end of cooling fan shroud.
Disconnecting or connecting cooling fan shroud on top frame.
Disconnecting or connecting rear end of cooling fan shroud and removing or
installing cooling fan shroud and fan housings.
Fuel injection pump-installed view.
Removing or installing left rear upper cover.
Removing or installing fuel injector left tube clamps.
Removing or installing fuel injector right tube clamps.
Fuel injector tubes-installed view.
Disconnecting fuel injector tubes from fuel injection pump.
Disconnecting or connecting crankcase breather tube, electrical lead, throttle
control, and fuel return hose-engines prior to relocated crankcase
breather tube.
Disconnecting or connecting throttle control, fuel return hose, and electrical
lead-engines with relocated crankcase breather tube.
Disconnecting or connecting crankcase breather tube at front of engine.
Disconnecting or connecting rear intermediate crankcase breather tube at
tube tee-engines prior to relocated crankcase breather tube.
Removing or installing angle bracket from fuel injection pump.
Disconnecting or connecting fuel injection pump oil and fuel inlet hoses
Positioning fuel injection pump coupler by turning flywheel using splined
wrench - 5120-793-7895.
Page
4-10
4-10
4-11
4-12
4-12
4-13
4-13
4-14
4-14
4-15
4-15
4-16
4-16
4-16
4-17
4-17
4-18
4-18
4-19
4-20
4-20
4-21
4-21
4-22
4-23
4-24
4-24
4-25
4-25
4-26
4-26
4-26
4-26
4-27
vi
Back to Top
