TM-9-2815-200-35
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED ,12 - CYLINDER , ASSEMBLY ;MODELS AVDS-1790-2M (2815-856-4996), AVDS-1790-2A AND AVDS-1790-2AM (2815-856-9005)
TECHNICAL MANUAL; DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
TM-9-2815-200-35 - Page 16 of 779
Figure
Number
4-157
4-158
4-159
4-160
4-161
4-162
4-163
4-164
4-165
4-166
4-167
4-168
4-169
4-170
4-171
4-172
4-173
4-174
4-175
4-176
4-177
4-178
4-179
4-180
4-181
4-182
4-183
4-184
4-185
4-186
4-187
4-188
4-189
4-190
4-191
4-192
4-193
4-194
4-195
4-196
4-197
4-198
x
Title
Removing or installing valve rocker arm cover bolts and removing valve
rocker arm cover.
Rem oving or installing valve adjusting screw.
Removing or installing valve rocker arm shaft plugs.
Removing valve rocker arm shafts and valve rocker arms.
Installing valve rocker arms and valve rocker arm shafts.
Installing valve rocker arm cover.
Positioning lip of intercylinder preformed hose.
Positioning valve adjusting screw pad on end of valve stem.
Torque tightening fuel injector nozzle.
Fuel injector nozzle and holder assembly,
Fuel injector nozzle and holder assembly—sectional view.
Testing fuel injector nozzle and holder assembly.
Partial disassembly or assembling fuel injector nozzle and holder assembly.
Disassembling or assembling fuel injector nozzle components.
Removing or installing transmission drive gearshaft and flywheel mounting
bolts.
Removing transmission drive gearshaft using bolts as puller screws.
Installing eye bolt - 5306-050-0348.
Removing or installing flywheel.
Removing or installing crankshaft oil seal retainer.
Removing or installing oil seal cap and oil seal housing mounting bolts.
Removing oil seal housing using mechanical pullers - 5120-473-7222.
Removing or installing oil seal housing cap and housing.
Removing or installing crankshaft oil seal,
Removing crankshaft oil seal spring.
Installing crankshaft oil seal spring.
Correct position for crankshaft oil seal split line before installing seal retainer.
Installing flywheel, rising bolts to draw flywheel against crankshaft.
Installing or removing compression adapter - 4910-795-7961 (cylinder
compression test ).
Checking cylinder compression using gage assembly - 4910-870-6283 and
compression adapter - 4910-795-7961.
Removing or installing valve adjusting screw cover plates - right side,
Removing or installing valve adjusting screw cover plates - left side.
Setting exhaust valve clearance using thickness gage blade -5210-793-7899.
Setting intake valve clearance using thickness gage blade -5210-793-7898,
Flywheel timing mark locations.
Disconnecting or connecting oil cooler inlet and outlet hoses.
Removing or installing engine and transmission oil coolers.
Removing or installing oil cooler end shroud.
Removing or installing intake valve cover plate.
Cross section of cylinder 6R showing position of camshaft lobes for valve
timing.
Flywheel timing marks alined with pointer for valve timing - right bank of
cylinders.
Setting intake valve clearance for cylinders 6R using thickness gage blade -
Removing or installing camshaft gear housing cover.
Page
4-77
4-78
4-78
4-78
4-78
4-79
4-79
4-80
4-80
4-81
4-82
4-83
4-84
4-85
4-88
4-88
4-89
4-89
4-90
4-90
4-91
4-91
4-91
4-91
4-92
4-92
4-93
4-94
4-95
4-96
4-97
4-98
4-98
4-98
4-99
4-99
4-100
4-100
4-100
4-101
4-101
4-102
Back to Top
