TM-9-2815-200-35
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED ,12 - CYLINDER , ASSEMBLY ;MODELS AVDS-1790-2M (2815-856-4996), AVDS-1790-2A AND AVDS-1790-2AM (2815-856-9005)
TECHNICAL MANUAL; DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
TM-9-2815-200-35 - Page 22 of 779
Figure
Number
5-170
5-171
5-172
5-173
5-174
5-175
5-176
5-177
5-178
5-179
5-180
5-181
5-182
5-183
5-184
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-8
6-9
6-10
6-11
6-12
6-13
6-14
6-15
6-16
6-17
6-18
6-19
6-20
6-21
6-22
xvi
Title
Removing accessory drive gear using mounting bolts as puller screws.
Removing or installing crankcase tie rod attaching parts - right front view.
Removing or installing tie rods and attaching parts - left side view.
Removing or installing main bearing attaching parts.
Removing main bearing cap using crankcase spreading tool - 5120-575-
7767, mechanical adapter -5120-837-5091, and mechanical puller -5120-
310-4668.
Crankshaft with main bearing caps removed showing correct position of
crankshaft counterweights
before removal or after installation of
crankshaft.
Installing or removing crankshaft and connecting rod sling -4910-795-7955
at crankshaft flywheel flange.
Installing or removing crankshaft and connecting rod sling - 4910-795-7955
at crankshaft torsional vibration damper flange.
Removing or installing crankshaft and connecting rod assemblies using
crankshaft and connecting rod sling - 4910-795-7955.
Removing or installing upper main sleeve bearing halves.
Removing or installing piston oiler nozzle assemblies.
Rem oving or installing starter and generator idler gearshaft flange nuts.
Removing starter and /or generator idler gearshaft.
Removing or installing starter driven gearshaft bearing cage attaching parts.
Removing or installing starter gearshaft bearing cage.
Standard and oversize stud identification.
Removing helical-coil threaded insert from cylinder assembly using screw
thread extractor -5120-251-1527.
Installing helical-coil threaded insert in cylinder assembly using screw thread
inserter -5120-797-2407.
Engine name plate.
Removing or installing pipe plugs and fuel pump driven gearshaft
replacement cover.
Removing or installing pipe plugs and fuel supply pump adapter replacement
cover.
Removing or installing crankcase oil gallery pipe plugs.
Removing or installing crankcase from engine overhaul stand using im-
provised rope sling.
Crankcase oil passages - schematic diagram.
Checking torque of main bearing cap studs.
Checking clearance between upper main thrust bearing flange and crankcase.
Checking inside diameter of main bearings.
Crankcase restricted welding areas,
Points of measurement for checking crankcase.
Crankcase studding - ¾ right rear exposed view.
Crankcase studding - ¾ left rear view.
Crankcase studding - bottom view.
Rem oving or installing transmission adapter lifting eye and timing pointer.
Pressing starter driven gearshaft and bearings from bearing cage.
Pressing starter driven gearshaft from ball bearings.
Starter drive gear - rework.
Pressing ball bearings on starter driven gearshaft.
Page
5-97
5-98
5-99
5-100
5-101
5-102
5-103
5-103
5-104
5-105
5-105
5-106
5-106
5-106
5-107
6-7
6-8
6-9
6-11
6-12
6-12
6-13
6-14
6-15
6-16
6-16
6-17
6-19
6-20
6-21
6-21
6-22
6-24
6-25
6-25
6-26
6-27
Back to Top
