TM-9-2815-200-35
ENGINE, WITH CONTAINER:TURBOSUPERCHARGED, DIESEL ,FUEL INJECTION ,90-DEGREE “V” TYPE, AIR - COOLED ,12 - CYLINDER , ASSEMBLY ;MODELS AVDS-1790-2M (2815-856-4996), AVDS-1790-2A AND AVDS-1790-2AM (2815-856-9005)
TECHNICAL MANUAL; DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
TM-9-2815-200-35 - Page 21 of 779
Figure
Number
Title
5-134
5-135
5-136
5-137
5-138
5-139
5-140
5-141
5-142
5-143
5-144
5-145
5-146
5-147
5-148
5-149
5-150
5-151
5-152
5-153
5-154
5-155
5-156
5-157
5-158
5-159
5-160
5-161
5-162
5-163
5-164
5-165
5-166
5-167
5-168
5-169
Location of preformed packings at oil transfer tubes in crankcase assembly -
rear fan and accessory drive housing mounting base.
Removing or installing oil pan rear bolts.
Removing or installing oil pan bolts - right front view.
Removing or installing oil pan.
Removing or installing crankshaft damper and oil filter housing attaching
parts.
Removing or installing crankshaft damper and oil filter housing.
Front end of crankcase assembly showing locations of oil transfer tube
preformed packings.
Disconnecting or connecting cylinder deflectors at cylinders.
Removing or installing lower cylinder deflector straps and deflectors - right
side.
Checking breaking torque of cylinder base nuts, using box wrench - 5120-
678-5287.
Right bank cylinders in vertical position for removing or installing cylinders
from crankcase.
Removing cylinder No. lR.
Removing piston pin and piston - cylinder No. lR.
Engine with cylinder assemblies and pistons removed showing crankcase
protectors - 4910-795-7951 installed.
Removing or installing scavenge oil pickup, oil pan pressure relief tube, and
oil spill tube.
Removing or installing oil pump assembly.
Removing or installing oil pressure sending unit, oil pressure warning switch
and generator air intake tube support brackets.
Removing or installing fuel pump drive coupling adapter and coupling.
Removing crankshaft torsional vibration damper using mechanical pullers -
Removing or installing starter drive adapter.
Removing or installing starter driven gear attaching parts.
Removing starter driven gear.
Removing or installing generator drive adapter attaching parts - engines with
mounting nuts.
Removing or installing generator drive adapter attaching parts - engines with
mounting studs.
Removing or installing generator drive adapter and associated parts.
Removing or installing transmission drive gearshaft attaching parts.
Removing transmission drive gearshaft assembly using mounting bolts as
puller screws.
Preparing flywheel for removal.
Removing flywheel using eye bolt - 5306-050-0348.
Removing or’ installing transmission adapter attaching parts.
Removing or installing transmission adapter.
Removing or installing crankshaft oil seal retainers.
Removing or installing crankshaft oil seal cap and housing attaching parts.
Removing or installing oil seal cap and housing.
Removing or installing oil seal housing support.
Removing or installing accessory drive gear attaching parts.
Page
5-74
5-75
5-75
5-76
5-76
5-77
5-78
5-78
5-79
5-80
5-80
5-81
5-82
5-83
5-84
5-85
5-86
5-87
5-87
5-88
5-88
5-89
5-89
5-90
5-90
5-91
5-91
5-92
5-92
5-93
5-94
5-94
5-95
5-95
5-96
5-97
xv
Back to Top
