TM-9-2815-205-34
ENGINE WITH CONTAINER; MODELS 5063-5299, 5063-5392, 5063-5393, 5063-5395, 5063-5398, 5063-539F, 5063-539L
TECHNICAL MANUAL; DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
AUGUST 1992
TM-9-2815-205-34 - Page 91 of 596
TM 9-2815-205-34
2-24. TURBOCHARGER OIL SUPPLY LINE REMOVAL/INSTALLATION
This task covers: a. Removal
b. Installation
INITIAL SETUP
MODELS
MATERIALS/PARTS
All except model 5063-5299
1
Lockwasher (App F, Item 99)
TOOLS AND SPECIAL TOOLS
Tool kit, general mechanics (App B, Item 107)
Wrench, torque (App B, Item 116)
a. Remova l
(1) Disconnect hose assembly (1) from connector (2) in top of turbocharger (3).
(2) Remove screw (4) and Iockwasher (5) from clip (6) on hose assembly (1) at plate (7) on rear of
left cylinder head. Discard Iockwasher. If necessary, remove clip from hose assembly.
(3) For model 5063-5392, remove screw (8), flat washer (9), Iockwasher (10), and nut (11) from clip
(12) on hose assembly (1) and from bracket (13) on air inlet housing. Discard Iockwasher. If
necessary, remove clip from hose assembly.
(4) For models 5063-5393 and 5063-539L, remove screw (14) and lockwasher (15) from clip (16)
on hose assembly (1) at left side of flywheel housing. Replace screw and Iockwasher. If
necessary, remove clip from hose assembly.
(5) Disconnect hose assembly (1) from oil filter adaptor (17), Refer to Para 2-12 for model
5063-5392, Para 2-13 for models 5063-5393 and 5063-539L, Para 2-14 for model 5063-5395
and 5063-539F, and Para 2-15 for model 5063-5398,
b. Installation
(1)
(2)
(3)
(4)
(5)
2-64
Connect hose assembly (1) to connector (2) in top of turbocharger (3). Tighten securely.
Connect hose assembly (1) to oil filter adaptor (17). Refer to Para 2-12 for model 5063-5392,
Para 2-13 for models 5063-5393 and 5063-539L, Para 2-14 for model 5063-5395 and
5063-539F, and Para 2-15 for model 5063-5398,
Remove screw (4) and Iockwasher (5) from plate (7) at rear of left cylinder head and install
screw and Iockwasher in clip (6) and plate. Torque screw to 30-35 Ib-ft (41-47 N•m).
For model 5063-5392: If removed, install clip (12) on hose assembly (1). Install screw (8), flat
washer (9), Iockwasher (10), and nut (11) in clip on hose assembly and in bracket (13) on air
inlet housing. Torque screw to 30-35 Ib-ft (41-47 N•m).
For models 5063-5393 and 5063-539L: If removed, install clip (16) on hose assembly (1),
Remove screw (14) and lockwasher (15) located at left side of flywheel housing. Install screw
(in clip on hose assembly) and Iockwasher on flywheel housing. Torque screw to 30-35 Ib-ft
(41-47 N•m).
Change 1
Back to Top
