I
Cotter pin aNd ±aT washER
2
MA²ual fuEL SHUt-off ³od “SSEmbly
3
µP¶I·g
4 Cpscr±w
¸¹d ºockw»¼½¾¶
6
ĀæEĆfĆloĆKI²g nuT, Oat waýĆĆ
ĀøNd ĆĆĆHINE BĆĆT
7
ĆĆRoTTĆĆ Ćo²TRol RoD a¼SĆĆBĆ>
8
ĀæElfĆĆoĆkiNG NĆTĆ ĆaĆ wA¼½ER
a²d ĆacHĆNE ĆoĆĆ
TM 9-2815±²²0³34
TA265647I
5
ĆĆGlĆ ĆRacĆĆT
Figure
²³ i. “µ
DIsco11±²ECtI³“G OR µo³“±“eµT¶³·¸ ¹¹“a³““ºA/ fUel SLmT»¼½¾¿od.
ĆhĀæĆĆĆĆĆ Ć
ĆĆ ĆnĆ aĆĆoƶaĆeĆ paĀæĆĆ, MĆĆeĆ
AV DS-1¶90·¸dR
e1Ƹó“eĆ
I
NOtE
The fuel injection pump coUpLing sleevEs
and Hubs must bE IDEntiFIeD w±th iDentica²
marks (³g.
“µ¶·)
tO prEvEnt mismating of
paR“sµ THe sleeves and Hubs arE matchEd
¶·¸ eacH assEmb¹y anD must nOt be IntEr-
cHangEd betWEen assEmblº»s¼
(¸¹.º»
POsitiOn imprOvisED enginE turning t½Ol
¼½,
Figµ
¾¿ĆĆĆĆĆ
on poWEr ¾aKEĀæOff cOĆplIng anD secuĆe
wĆth fouĆ
7/Āø6Ć
ĆĆUnF
x
Āø
V2Āæinch maCĆine bOlts
ĆĆĆĆ
Ć
nstall a
½
1/ĆĆincH soĆkEt
ĆĆĆ
anD ĆuĆ cranksHaft
until fuEl injection pump cOupling is pOsitiOnEĆ as
shoĆn in FiguĆE
“ö·Ć
Stamp iDentifiCation marĆs
On bOtH cOupling sleEvesĆ ĆemOvE four bOlts anD
ĆOCk ĆasHers (ĆgĆ
¾ĆĆĆĆ
anD ĆOck p¹atEs anD separate
cOupĆĀŗng s²EEvEsĆ
NOĆe
THE fue¹ inJeĆtion pump CouplIng sleevEs
anD hubs must be iDenti¶iED ĆĆth iDEntical
marks ógĆ
“µ¶ĆĆ
tO prEvent misMating OĆ
partsĆ ĆhE sleevEs anĆ Hubs arE matĆHeD
fOr each assembly and must nOt bE inter-
cHangeD bEtĆeEn assembliesĆ
ĆĀŗ6Ā»
Ćut lOckIng ĆĆ Ć”E ĆĆgĆ¢
¾ĆĆĆĆ
and remOvE
three machinE bOlts and p¹ain ĆasHeĆ”sĆ¢ Ć£OOsen
¹OƤeĀø rear bOlt untIl tHĀøeads aĀøĆ„ ĆĆeeƦ Bo¹t cannOt
bE rEmOved untI¹ a¶ter ¶uEl inçeCtIOn pump Is ÔEè
mOveD éêOm EngĆ«nEµ ĆEmOve ¶uEl ĀŗnƧeĆtIOn pump
frOm mOunting baseĆ¢ ƬemOvE anD DisCarD preĆ
î¸meD packºng ïðOm mOunting base oñl trans¶er
òubEĆ ĆemOóe boLt anD Ć“lain ĆasHerĆ¢
Ta¹º»¼½¾
ĆĆĆĆĆe
ĀæĆĆĆĆ
ĆĆĆĆĀ“Ć1Ā“q ĆĆyĀ·Ćà Ôâã ·“äij“à æPlƧNĆØ<Ć
WĆeĆ
ĆĆĆĆ
éêëìl
Ć \ĆĆĆĆJĆĆĆĆĆĆ ĆnĆ Ć ĆĆ ĆĆĆĆĆĆĆĆt/
ĆîïðNñòó
ƵHAnGe
Ć
ĆĆĆĆ