TM-9-2815-205-34
ENGINE WITH CONTAINER; MODELS 5063-5299, 5063-5392, 5063-5393, 5063-5395, 5063-5398, 5063-539F, 5063-539L
TECHNICAL MANUAL; DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
AUGUST 1992
TM-9-2815-205-34 - Page 269 of 596
TM 9-2815-205-34
344. FLYWHEEL HOUSING REPLACEMENT
This task covers: a. Removal
b. Cleaning/Inspection
c. Installation
INITIAL SETUP
MODELS
EQUIPMENT CONDITION
All
TOOLS AND SPECIAL TOOLS
Tool kit, general mechanics (App B, Hem 107)
Wrench, torque (App B, Item 116)
Sling (App B, Item 93)
Guide studs (App D, Item 2)
Expander, oil seal (App B, Item 25)
MATERIALS/PARTS
Gasket (App F, Item 75)
Gasket (App F, Item 69)
Gasket (App F, Item 72)
Lockwashers (App F, Item 98)
Lockwashers (App F, Item 99)
Bolts, self-locking (App F, Item 15)
Bolts, self-locking (App F, Item 20)
(all except model 5063-5398)
Bolts, self-locking (App F, Item 14)
(model 5063-5398)
EXPENDABLE/DURABLE SUPPLIES
Oil, engine (App C, Item 26)
Grease (App C, Item 18)
Cleaning solvent (App C, Item 9)
Adhesive, gasket (App C, Item 1)
Para
3-3
3-5
3-6
3-23
3-28
3-29
3-30
3-33
3-40
Description
Turbocharger removed (models
5063-5393, 5063-5395, 5063-5398,
5063-539F, and 5063-539L)
Mounting bracket and exhaust tubes
removed (models 5063-5393 and
5063-539L)
Mounting bracket and exhaust tubes
removed (models 5063-5395, 5063-5398,
5063-539F)
Fuel pump removed
Tachometer drive adapter removed
(models 5063-5299,5063-5392,
5063-5393, 5063-539F
I
and 5063-539L)
Tachometer drive adapter removed
(models 5063-5395 and 5063-5398)
Blower drive supped removed
Oil pan removed
Flywheel removed
a. Removal
(1)
(2)
(3)
(4)
(5)
(6)
Thread two 3/8-16 eye bolts (1) into tapped holes located in pads at sides of flywheel housing
(2). Attach sling (3) to eye bolts.
Remove eight screws (4), eight Iockwashers (5), and eight flat washers (6) from area inside bell
of flywheel housing (2). Discard Iockwashers.
Thread two studs (7) into cylinder block inside bell area of flywheel housing (2).
Remove two large self-locking bolts (8), two flat washers 9), four small self-locking bolts (10),
and four flat washers (11) from area inside bell of flywheel housing (2). Discard bolts.
Remove two screws (12), two lockwashers (13), and two flat washers (14) from upper right side
of flywheel housing (2). Discard Iockwashers.
Remove two nuts (15), two Iockwashers (16), two screws (17), and two flat washers (18) from
upper left side of flywheel housing (2). Discard Iockwashers.
3-140
Change 1
Back to Top
